Difference between revisions of "Benderlink Ethernet Module"
(→Inside the Module) |
(→Inside the Module) |
||
| Line 78: | Line 78: | ||
===Inside the Module=== | ===Inside the Module=== | ||
| − | + | <table> | |
| − | + | <tr> | |
| − | + | <td width=300> | |
| − | + | This is an image of the inside of the module.<br><br> | |
*The Current Loop board is in the upper left corner.<br><br> | *The Current Loop board is in the upper left corner.<br><br> | ||
*The Ethernet Serial Device Server is the black box on the right.<br><br> | *The Ethernet Serial Device Server is the black box on the right.<br><br> | ||
| − | *The power supply is on the lower left.< | + | *The power supply is on the lower left. |
| − | + | </td> | |
| − | + | <td> | |
| + | [[image:Blink_module_vector_test3.jpg|300px]] | ||
| + | </td> | ||
| + | </table> | ||
===Other Applications=== | ===Other Applications=== | ||
Revision as of 16:40, 7 December 2009
Put SERIAL Port Benders on a Wireless or Wired NETWORK at Extended Distances
|
The module connects any bender or measuring center devices through your Ethernet network to a bender that normally connects using only standard RS-232 signals. It gives your bender or measuring center access to a virtual COM port anywhere on the network in your building. Distance limitations are removed with this protocol. We have WiFi (wireless) and WIRED TCP/IP models. |
|
Connect to EL Vector Tube Data Centers Using Current Loop Electronics
|
The module can even be equipped with our version of the Eaton Leonard current loop boards (our own model called the CB-EL1) to allow for 100% compatible Eaton Leonard legacy protocol through the network for connection to an EL Vector Tube Data Center |
|
Connect ROMER to Eaton Leonard Benders Using Current Loop Electronics
|
The module, equipped with our current loop electronics, can be used to connect the ROMER measuring center to Eaton Leonard benders. See ROMER to Eaton Leonard Benders |
|
Connect AICON to Eaton Leonard Benders Using Current Loop Electronics
|
The module, equipped with our current loop electronics, can be used to connect the AICON measuring center to Eaton Leonard benders. See AICON to Eaton Leonard Benders |
|
Cabling
| This is a module with cables in place. Three cables are attached to the wired version. A fourth wireless antenna cable is attached for wireless version. |
|
PINES TS-2000 to Eaton Leonard Tube Data Center
|
This is a single port Benderlink Ethernet Module that connected a TS-2000 (Pines) control to an Eaton Leonard Vector 1 measuring center. |
|
Inside the Module
|
This is an image of the inside of the module.
|
|
Other Applications
| Bender | Description | |
|---|---|---|
| PINES TS-2000 | Using Benderlink for Pines - Add a module to a Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| BLM VGP | Using Benderlink for BLM - Add a module to Vector Tube Data Center to enable a network connection through a current-loop module directly into the standard Vector bender port. | |
| ROMER to Eaton Leonard Bender | Add a module to any Eaton Leonard bender and make it wireless. | |
| CHIYODA | Add this module to a Chiyoda to allow it to communicate over the network from its RS-232 port. | |
| KEINS | Add this module to a KEINS to allow it to communicate over the network from its RS-232 port. | |
| MiiC | Works with a MiiC to place it on the network (See Benderlink for MiiC) | |
PDF DataSheets
|
|
Download a DataSheet for Benderlink Ethernet Module for Eaton Leonard
|
