Difference between revisions of "VTube-LASER v1.6"

From ATTWiki
Jump to: navigation, search
(25px ENHANCED: New Options in Part Setup)
(25px ENHANCED: New Options in Part Setup)
Line 66: Line 66:
 
New '''A-End Diameter''' and '''B-End Diameter''' is added to the Part Setup menu.<br><br>
 
New '''A-End Diameter''' and '''B-End Diameter''' is added to the Part Setup menu.<br><br>
 
The new diameters are used to qualify end-scans within the tolerance in System Options.<br><br>
 
The new diameters are used to qualify end-scans within the tolerance in System Options.<br><br>
[[image:vtube-laser_endscan_diameter_qualification_tolerance.jpg]]
+
[[image:vtube-laser_endscan_diameter_qualification_tolerance.jpg|200px]]
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>

Revision as of 22:05, 21 February 2011

Vtube-laser logo.jpg

Revision 1.6

Back to VTube-LASER

Vtube-laser 1 6.jpg



Check.jpg NEW: End Scan Outlier Detection

The end scan procedures in VTube-LASER are now enhanced to detect and remove outlier points in an end-scan.

In the context of VTube-LASER, an "outlier" is a point that falls outside the space of the actual surface being scanned.

The image at the right shows a side view of the result of an end-scan of a tube. The LLP (laser line probe) is positioned above the tube at the top of this image and is pointed downward in the direction of the left black arrow. The laser is moving downward along its path from the probe. It is then reflected back to the receiver of the scanner in the path of the right arrow.

Most of the points fall on the surface of the outside of the tube, inside the tube, or wall of the tube. However, there is also an outlier point present (enclosed in the red lines at the top). It cannot possibly part of the diameter. (These points were formed from a higher-than-normal reflective points on the inside of the diameter.

The outlier point is detected and then removed from the list of possibilities automatically because it is not close enough to the diameter or wall of the diameter.

This ensures repeatability of the end-scan process.

Vtube-laser endscan outlier detection.jpg



Check.jpg ENHANCED: New Features and Interface in Measure Setup

The new grid interface in in Measure Setup has more options.

New options include:

  • Continuous Scan on Tactile Cylinder-Scans: Scan points repeatedly whenever you press the green button.

  • Continuous Scan on Tactile End-Scans: Scan points repeatedly whenever you press the green button.

  • Automatic display of Master model: Show the master model with the current straight highlighted orange during measure.

Vtube-laser measuresetup grid.jpg
Vtube-laser measuresetup displayofmastermodel.jpg




Check.jpg ENHANCED: New Options in Part Setup

New A-End Diameter and B-End Diameter is added to the Part Setup menu.

The new diameters are used to qualify end-scans within the tolerance in System Options.

Vtube-laser endscan diameter qualification tolerance.jpg

Vtube-laser partsetup grid 1 6.jpg



Check.jpg ENHANCEMENT- Part Name is Used as Filename When Part Name Changes

In previous versions, the part name was used as the filename only if the previous filename was empty.

Now - when the part name changes, the part name is used as the initial filename in the Save dialog.

Vtube savefile partname.jpg




Check.jpg ENHANCED- Linear Units Now Set By Single Large Button

In previous versions, the linear units radio buttons were not reliable in setting the proper state.

Plus they were too small to easily press.

This version removes these radio buttons and uses an large button with either an M or an I that toggles the state.

These buttons can also be localized. The M and I can be changed to other Unicode characters for other languages.

Old Interface:
Vtube laser linear units.jpg
New Interface:
Vtube laser linear units button millimeter.jpg
Vtube laser linear units button inch.jpg



Check.jpg REPAIR- Laser Active Initialization

In previous versions, VTube required the operator to enter Measure Setup at least one time when coming into Laser Mode in order to setup the Laser active mode.

This has been corrected in this version. It is no longer necessary to enter measure setup if you know the setup is correct.

Vtube laser measuresetup.jpg




Check.jpg Other Changes

  • The report window now requires an operator to close the window before using any other part of VTube.


  • The print preview window buttons are re-arranged so that they are larger and easier to press. The Print button is moved to the right side of the window.


  • If VTube changes from cylinder fit to centerline projection mode during a measurement, VTube will now always consider the measure a cylinder fit failure.



Check.jpg Changes to VTube-STEP



Check.jpg Issues with this version fixed in next version

  • No known issues

Other Pages