Difference between revisions of "Benderlink Ethernet Module for PINES to Vector"
From ATTWiki
| Line 1: | Line 1: | ||
| − | [[image:Blinklines2vector_pdfimage.jpg|400px]] | + | [[image:Blinklines2vector_pdfimage.jpg|400px|right]] |
| + | |||
| + | [[image:Blink_module_vector_test2.jpg|400px]] | ||
| + | <br><br> | ||
| + | __TOC__ | ||
| + | |||
| + | |||
| + | ==Description== | ||
| + | This is a single port Benderlink Ethernet Module that works with Benderlink for Pines to connect a TS-2000 (Pines) control to an Eaton Leonard Vector 1 measuring center. | ||
| + | <br><br> | ||
| + | |||
| + | ==Productivity Benefits== | ||
| + | 100% Eaton Leonard Vector 1 Compatible. Any standard Vector 1 bender port can connect with this module. | ||
| + | |||
| + | ==Installation Location== | ||
| + | It is placed near the Vector 1 Laservision measuring center. | ||
| + | |||
| + | ==About the Connections== | ||
| + | |||
| + | * One RJ-45 port - This connects to the Ethernet. | ||
| + | * One Military Connector - This connector follows the legacy Eaton Leonard style connection. You can connect standard communications cable with circular connectors at either end. | ||
| + | * One Power Port - Any voltage from 90 to 264 VAC accepted. | ||
| + | <br> | ||
| + | |||
| + | |||
| + | ==Inside the Module== | ||
| + | |||
| + | |||
| + | {| border="0" cellpadding="5" cellspacing="0" align="none" width=700 | ||
| + | |- | ||
| + | | This is an image of the inside of the module.<br><br> | ||
| + | *The Current Loop board is in the upper left corner.<br><br> | ||
| + | *The Ethernet Serial Device Server is the black box on the right.<br><br> | ||
| + | *The power supply is on the lower left.<br><br> | ||
| + | | [[image:Blink_module_vector_test3.jpg|400px]] | ||
| + | |} | ||
| + | |||
| + | ==Example Installation== | ||
| + | <br> | ||
| + | This is an image of the box installed on a test bench computer running Benderlink for Eaton Leonard, which simulates Vector 1 Laservision communications.<br> | ||
| + | <br> | ||
| + | [[image:Blink_module_vector_test1.jpg|300px]] | ||
| + | |||
| + | ==Purchasing== | ||
| + | <BR> | ||
| + | This item can be purchased from our [http://advanced-tubular-technologies.stores.yahoo.net/beculomo4po.html Online Store] | ||
| + | |||
| + | ==Other Pages== | ||
| + | |||
| + | *[[Benderlink Current Loop Module]] page | ||
| + | *[[Benderlink]] page | ||
| + | *Read more about the current loop board here: [[Communications Board for Eaton Leonard - CB-EL1]] | ||
Revision as of 13:11, 2 May 2008
Contents |
Description
This is a single port Benderlink Ethernet Module that works with Benderlink for Pines to connect a TS-2000 (Pines) control to an Eaton Leonard Vector 1 measuring center.
Productivity Benefits
100% Eaton Leonard Vector 1 Compatible. Any standard Vector 1 bender port can connect with this module.
Installation Location
It is placed near the Vector 1 Laservision measuring center.
About the Connections
- One RJ-45 port - This connects to the Ethernet.
- One Military Connector - This connector follows the legacy Eaton Leonard style connection. You can connect standard communications cable with circular connectors at either end.
- One Power Port - Any voltage from 90 to 264 VAC accepted.
Inside the Module
This is an image of the inside of the module.
|
|
Example Installation
This is an image of the box installed on a test bench computer running Benderlink for Eaton Leonard, which simulates Vector 1 Laservision communications.
Purchasing
This item can be purchased from our Online Store
Other Pages
- Benderlink Current Loop Module page
- Benderlink page
- Read more about the current loop board here: Communications Board for Eaton Leonard - CB-EL1
