Difference between revisions of "VTube-LASER v1.6"

From ATTWiki
Jump to: navigation, search
 
(→‎25px NEW: Help Reference for LASER Mode)
Line 15: Line 15:
  
  
−
===[[image:Check.jpg|25px]] NEW: Help Reference for LASER Mode===
+
===[[image:Check.jpg|25px]] NEW: End Scan Outlier Detection===
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=200>
 
<td width=200>
−
Now VTube-LASER has its own help reference.<br><br>
+
The end scan procedures in VTube-LASER are now enhanced to include outlier point detection.<br><br>
−
[[image:vtube-laser_help_button.jpg|200px]]
+
This is critical for situations where points may be detected that are too far from the diameter to be considered actual useful points in end-scans.
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
−
[[image:vtube-laser_help_reference.jpg|300px]]
+
[[image:vtube-laser_endscan_outlier_detection.jpg|300px]]
 
</td>
 
</td>
 
</tr>
 
</tr>

Revision as of 21:10, 21 February 2011

Vtube-laser logo.jpg

Revision 1.6

Back to VTube-LASER

Vtube-laser 1 6.jpg



Check.jpg NEW: End Scan Outlier Detection

The end scan procedures in VTube-LASER are now enhanced to include outlier point detection.

This is critical for situations where points may be detected that are too far from the diameter to be considered actual useful points in end-scans.

Vtube-laser endscan outlier detection.jpg



Check.jpg REPAIR: Mix ball probe and laser measurement

Using ball probe measurements on the end scans and and laser measurements in the cylinder straights now offsets the ball radius point properly in every case.

Vtube-laser ballprobe endscan.jpg




Check.jpg ENHANCEMENT- Part Name is Used as Filename When Part Name Changes

In previous versions, the part name was used as the filename only if the previous filename was empty.

Now - when the part name changes, the part name is used as the initial filename in the Save dialog.

Vtube savefile partname.jpg




Check.jpg ENHANCED- Linear Units Now Set By Single Large Button

In previous versions, the linear units radio buttons were not reliable in setting the proper state.

Plus they were too small to easily press.

This version removes these radio buttons and uses an large button with either an M or an I that toggles the state.

These buttons can also be localized. The M and I can be changed to other Unicode characters for other languages.

Old Interface:
Vtube laser linear units.jpg
New Interface:
Vtube laser linear units button millimeter.jpg
Vtube laser linear units button inch.jpg



Check.jpg REPAIR- Laser Active Initialization

In previous versions, VTube required the operator to enter Measure Setup at least one time when coming into Laser Mode in order to setup the Laser active mode.

This has been corrected in this version. It is no longer necessary to enter measure setup if you know the setup is correct.

Vtube laser measuresetup.jpg




Check.jpg Other Changes

  • The report window now requires an operator to close the window before using any other part of VTube.


  • The print preview window buttons are re-arranged so that they are larger and easier to press. The Print button is moved to the right side of the window.


  • If VTube changes from cylinder fit to centerline projection mode during a measurement, VTube will now always consider the measure a cylinder fit failure.



Check.jpg Changes to VTube-STEP



Check.jpg Issues with this version fixed in next version

  • No known issues

Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=VTube-LASER_v1.6&oldid=16016"