Difference between revisions of "VTube-STEP v2.9.5"

From ATTWiki
Jump to: navigation, search
(25pxNEW - BEND-TECH 7X IMPORT)
(Revision 2.9.5)
 
(One intermediate revision by one user not shown)
Line 4: Line 4:
 
[[image:vtube-step_logo_2.png|300px]]
 
[[image:vtube-step_logo_2.png|300px]]
 
==Revision 2.9.5==
 
==Revision 2.9.5==
Build: <br>
+
Release Date: March 2, 2018<br>
Release Date: Not Released<br>
+
  
  
Line 178: Line 177:
  
 
<td width=400>
 
<td width=400>
If any bend angle is less than 0.1 degrees, then VTube will now issue a warning in the header above the viewport.
+
If any bend angle is less than 0.1 degrees, VTube will now issue a "Zero-degree bend" warning in the header above the viewport.
 
</td>
 
</td>
  

Latest revision as of 00:04, 14 March 2018

Vtube-step logo 2.png

Revision 2.9.5

Release Date: March 2, 2018


Vtube-step v2.9 mainscreen headerassembly purple.png



Contents




Check.jpgENHANCED - FASTER USER INTERFACE

VTube is now faster due to some important changes to the user interface.




Check.jpgNEW - BEND-TECH 7X IMPORT

Now VTube can import the new BEND-TECH 7x format as well as the older version 6 format.

Vts 2.9.5 bend-tech 7x import.png



Check.jpgNEW - DENGLER VDS IMPORT (XYZ Data)

VTube can now import DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.)

Vts 2.9.5 dengler vds import.png




Check.jpgNEW - DENGLER VDS EXPORT(XYZ Data)

VTube can now exportDENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.)

Vts 2.9.5 dengler vds export.png



Check.jpgFIX - SOLID MODEL IMAGE PRINT IN REPORTS

VTube is designed to handle multiple displays.

We discovered that, for windows arrangements where the Windows Desktop is not on the far left monitor, VTube might not print the graphics image properly in reports.

This has been fixed in this version.

Vtl report header.png




Check.jpgFIX - REPAIRED LOSS OF ORIGINAL ORIENTATION DURING REVERSE CALC

VTube always attempts to keep the original XYZ orientation when you perform a Reverse Calc from LRA to centerline XYZ data.

We discovered that certain situations would cause VTube to lose the orientation during Reverse Calc.

This has been fixed in this version.

Vts 2.9.5 reversecalc loss orientation.png

Vts 2.9.5 reversecalc noloss orientation.png



Check.jpgFIX - BUILD TO TUBE TO SOLIDWORKS

VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly.

Since VTube is building a single tube in SOLIDWORKS the best action is to always build a single part drawing.

The build logic has been fixed in this version.

If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly.

Vts 2.9.5 swtrans.png




Check.jpgNEW - MINIMUM CLAMP LENGTH

VTube has a new Minimum Clamp Length field in the Part Setup menu.

If any bender data length is shorter than the minimum clamp length, then VTube will now issue a warning in the header above the viewport.

Vts 2.9.5 minimum clamp length.png



Check.jpgNEW - ZERO-DEGREE BEND ANGLE WARNING

If any bend angle is less than 0.1 degrees, VTube will now issue a "Zero-degree bend" warning in the header above the viewport.

Vts 2.9.5 zero-degree bend.png



Other Pages