Difference between revisions of "VTube-STEP v2.9.18"
From ATTWiki
(→25pxSelection Inversion Added) |
(→25pxNEW - Selection Inversion Method Helps Select Parts in an Assembly) |
||
| (6 intermediate revisions by one user not shown) | |||
| Line 24: | Line 24: | ||
| − | ==[[image:Check.jpg|25px]]Selection Inversion | + | ==[[image:Check.jpg|25px]]NEW - Selection Inversion Method Helps Select Parts in an Assembly== |
<table cellpadding=10 width=1400> | <table cellpadding=10 width=1400> | ||
| Line 30: | Line 30: | ||
<td width=300> | <td width=300> | ||
| − | Selection inversion makes selecting parts from inside an assembly much easier. | + | Selection inversion makes selecting parts from inside an assembly much easier.<br><br> |
| + | See the slides on the right to see how selection inversion is used.<br><br> | ||
| + | [[image:vts_2.9.18_selectioninversion_menu.png|300px]] | ||
</td> | </td> | ||
<td> | <td> | ||
| − | + | [[image:vts_2.9.18_selectioninversion1.png|600px]]<br><br> | |
| + | [[image:vts_2.9.18_selectioninversion2.png|600px]]<br><br> | ||
| + | [[image:vts_2.9.18_selectioninversion3.png|600px]]<br><br> | ||
| + | [[image:vts_2.9.18_selectioninversion4.png|600px]]<br><br> | ||
</td> | </td> | ||
| Line 73: | Line 78: | ||
<td> | <td> | ||
[[image:vtl_v2.9.18_DefaultRadius123.png|400px]] | [[image:vtl_v2.9.18_DefaultRadius123.png|400px]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</td> | </td> | ||
| Line 100: | Line 87: | ||
==[[image:Check.jpg|25px]]Other Changes== | ==[[image:Check.jpg|25px]]Other Changes== | ||
| − | |||
*NEW - Autobuild Parametrics now calculates the CUT LENGTH automatically in VTube-STEP.<br><br> | *NEW - Autobuild Parametrics now calculates the CUT LENGTH automatically in VTube-STEP.<br><br> | ||
| − | |||
Latest revision as of 20:37, 13 March 2019
|
Version 2.9.18Release Date: March 12, 2019
|
|
Contents |
NEW - Selection Inversion Method Helps Select Parts in an Assembly
|
Selection inversion makes selecting parts from inside an assembly much easier. |
|
NEW - OMCG SVNET Communications Protocol
|
This protocol allows you to correct OMCG benders. |
|
NEW - Now VTube has THREE Default Radii
| Radius 1, Radius 2, and Radius 3 are now available in Part Setup. |
|
Other Changes
- NEW - Autobuild Parametrics now calculates the CUT LENGTH automatically in VTube-STEP.
Other Pages
- Back to VTube-LASER
- Back to VTube Software Updates (for LASER Mode)
- See also VTube-STEP
- See also VTube-STEP Revisions
- See Customer Support Page to download the latest version.
