Difference between revisions of "VTube-STEP v2"

From ATTWiki
Jump to: navigation, search
(Created page with "<table> <tr cellpadding=10> <td width=225> 300px ==Revision 2.0== * Back to VTube-STEP * Back to VTube-STEP Revisions * Back to VTube S...")
 
(25px ENHANCED: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations)
 
(47 intermediate revisions by one user not shown)
Line 24: Line 24:
  
  
===[[image:Check.jpg|25px]] NEW: Path Manager===
+
===[[image:Check.jpg|25px]] NEW: VTube Path Manager - Saves Time By Storing Important Paths===
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
 +
This change to VTube is a huge time-saver.  Customers that have tested this feature report that they are very happy it.<br><br>
 
The new Path Manager allows you to store and recall complex file paths from VTube without having to constantly drill down into folders and paths.<br><br>
 
The new Path Manager allows you to store and recall complex file paths from VTube without having to constantly drill down into folders and paths.<br><br>
This is a huge time-saver alone.
+
The window displays when you open projects and perform imports.  It also opens when you perform a Save As project.
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
[[image:vtube-step-1.99_exportCSMM4.png|400px]]
+
[[image:vtube-step-2_screenimage_closeup_2.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 38: Line 39:
  
  
===[[image:Check.jpg|25px]] NEW: Springback Compensation Switch in Alpine M4 Export Menu===
+
===[[image:Check.jpg|25px]] NEW: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations===
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
The Alpine M4 Export menu now includes a Springback Compensation switch to enable or disable compensation.<br><br>
+
The Supravision network engine now allows for rotations to be inverted for benders that have rotations that move in the opposite direction to VTube.</td>
For springback compensation to be effective, it is necessary to have values other than 0 in the proportional and fixed springback fields in the Part Setup menu.
+
</td>
+
 
<td width=400>
 
<td width=400>
[[image:vtube-step-1.99_alpineexport_springback_option.png|400px]]
+
[[image:vtube-2_cwrotation_svnetwork.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
  
 
+
===[[image:Check.jpg|25px]] ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved===
===[[image:Check.jpg|25px]] NEW: Springback Compensation Switch in CSM M4 Export Menu===
+
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
The CSM M4 Export menu now includes a Springback Compensation switch to enable or disable compensation.<br><br>
+
* The CSM and Alpine conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.<br><br>
For springback compensation to be effective, it is necessary to have values other than 0 in the proportional and fixed springback fields in the Part Setup menu.
+
* Other adjustments and fixes to the conversion were tested with both styles of bender controls.<br><br>
 +
* When VTube sends corrections to the M4 controls, it now changes the adjustment values rather than the nominal values in the YBC page.
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-step-1.99_csmexport_springback_option.png|400px]]
+
[[image:alpinebender.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
 +
<br><br>
 +
 +
===[[image:Check.jpg|25px]] Other Changes===
 +
* The VTube configuration file location was changed to the more standard '''"c:\ProgramData\VTube"''' location.<br><br>
 +
* The installation performs a better job of setting up the configuration file location.<br><br>
 +
* The Supravision network engine has been enhanced to handle data files that don't follow the Supravison spec perfectly.<br><br>
 +
* We fixed a ball probe measurement issue where VTube would sometimes not always take in single points from the FARO driver.  This issue created problems with measuring cut planes too.  If you measured cut planes, and still couldn't get the cut plane to work properly, then it was probably due to this issue.<br><br><br>
  
 
==Other==
 
==Other==

Latest revision as of 23:36, 16 February 2015

Vtube-step logo.jpg

Revision 2.0

Vtube-step-1.87 screenimage.png





Check.jpg NEW: VTube Path Manager - Saves Time By Storing Important Paths

This change to VTube is a huge time-saver. Customers that have tested this feature report that they are very happy it.

The new Path Manager allows you to store and recall complex file paths from VTube without having to constantly drill down into folders and paths.

The window displays when you open projects and perform imports. It also opens when you perform a Save As project.

Vtube-step-2 screenimage closeup 2.png


Check.jpg NEW: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations

The Supravision network engine now allows for rotations to be inverted for benders that have rotations that move in the opposite direction to VTube.

Vtube-2 cwrotation svnetwork.png

Check.jpg ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved

  • The CSM and Alpine conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.

  • Other adjustments and fixes to the conversion were tested with both styles of bender controls.

  • When VTube sends corrections to the M4 controls, it now changes the adjustment values rather than the nominal values in the YBC page.

Alpinebender.png



Check.jpg Other Changes

  • The VTube configuration file location was changed to the more standard "c:\ProgramData\VTube" location.

  • The installation performs a better job of setting up the configuration file location.

  • The Supravision network engine has been enhanced to handle data files that don't follow the Supravison spec perfectly.

  • We fixed a ball probe measurement issue where VTube would sometimes not always take in single points from the FARO driver. This issue created problems with measuring cut planes too. If you measured cut planes, and still couldn't get the cut plane to work properly, then it was probably due to this issue.


Other