Difference between revisions of "VTube-STEP v1.59"
From ATTWiki
| (10 intermediate revisions by one user not shown) | |||
| Line 16: | Line 16: | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] FIX- Supravision Output Fix to the Rotation Values=== |
<table> | <table> | ||
| Line 22: | Line 22: | ||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
| − | + | The rotation values are now recorded properly in the Supravision output files and the Supravision data sent through the bender interface menu.</td> | |
| − | + | ||
| − | The | + | |
| − | </td> | + | |
<td> | <td> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 34: | Line 30: | ||
<br> | <br> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] ENHANCEMENT- Part Name is Used as Filename When Part Name Changes === |
| − | + | ||
<table> | <table> | ||
| − | |||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
| − | + | In previous versions, the part name was used as the filename only if the previous filename was empty. | |
| − | </td> | + | <br><br> |
| + | Now - when the part name '''changes''', the part name is used as the initial filename in the Save dialog.</td> | ||
<td> | <td> | ||
| + | [[image:vtube_savefile_partname.jpg]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] ENHANCED- Linear Units Now Set By Single Large Button === | ||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=200> | ||
| + | In previous versions, the linear units radio buttons were not reliable in setting the proper state. | ||
| + | <br><br> | ||
| + | Plus they were too small to easily press. | ||
| + | <br><br> | ||
| + | This version removes these radio buttons and uses an large button with either an M or an I that toggles the state. | ||
| + | <br><br> | ||
| + | These buttons can also be localized. The M and I can be changed to other Unicode characters for other languages.</td> | ||
| + | <td> | ||
| + | Old Interface: | ||
| + | <br> | ||
| + | [[image:vtube_laser_linear_units.jpg]] | ||
| + | <br> | ||
| + | New Interface: | ||
| + | <br> | ||
| + | [[image:vtube_laser_linear_units_button_millimeter.jpg]] | ||
| + | <br> | ||
| + | [[image:vtube_laser_linear_units_button_inch.jpg]] | ||
| + | <br> | ||
| + | </td> | ||
| + | </tr> | ||
</table> | </table> | ||
| + | |||
| + | <br><br> | ||
==Other Pages== | ==Other Pages== | ||
*Back to the [[VTube]] page | *Back to the [[VTube]] page | ||
Latest revision as of 20:34, 21 February 2011
|
Revision 1.59
|
|
FIX- Supravision Output Fix to the Rotation Values
| The rotation values are now recorded properly in the Supravision output files and the Supravision data sent through the bender interface menu. |
ENHANCEMENT- Part Name is Used as Filename When Part Name Changes
|
In previous versions, the part name was used as the filename only if the previous filename was empty.
|
|
ENHANCED- Linear Units Now Set By Single Large Button
|
In previous versions, the linear units radio buttons were not reliable in setting the proper state.
|
Old Interface:
|
Other Pages
- Back to the VTube page
