Difference between revisions of "VTube-LASER v2.9.5"
(→25pxNEW - DENGLER VDS EXPORT(XYZ Data)) |
(→Revision 2.9.5) |
||
| (8 intermediate revisions by one user not shown) | |||
| Line 6: | Line 6: | ||
==Revision 2.9.5== | ==Revision 2.9.5== | ||
| − | Release Date: | + | Release Date: March 2, 2018<br> |
| − | Build: | + | Build: 1 |
* Back to [[VTube-LASER]] | * Back to [[VTube-LASER]] | ||
| Line 34: | Line 34: | ||
<td> | <td> | ||
| + | [[image:VTL Single Tube with shadow.png|400px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 126: | Line 127: | ||
<td width=400> | <td width=400> | ||
| − | VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly.<br><br> | + | VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly.<br><br>If VTube is building a single tube in SOLIDWORKS the best action is to always build a single part drawing.<br><br> |
The build logic has been fixed in this version.<br><br> | The build logic has been fixed in this version.<br><br> | ||
If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly. | If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly. | ||
| Line 138: | Line 139: | ||
</table> | </table> | ||
<br><br> | <br><br> | ||
| − | |||
| − | |||
==[[image:Check.jpg|25px]]NEW - BEND-TECH 7X IMPORT== | ==[[image:Check.jpg|25px]]NEW - BEND-TECH 7X IMPORT== | ||
| Line 147: | Line 146: | ||
<td width=400> | <td width=400> | ||
| − | + | Now VTube can import the new BEND-TECH 7x format as well as the older version 6 format. | |
</td> | </td> | ||
| Line 157: | Line 156: | ||
</table> | </table> | ||
<br><br> | <br><br> | ||
| − | |||
==[[image:Check.jpg|25px]]NEW - DENGLER VDS IMPORT (XYZ Data)== | ==[[image:Check.jpg|25px]]NEW - DENGLER VDS IMPORT (XYZ Data)== | ||
| Line 188: | Line 186: | ||
<td> | <td> | ||
[[image:vts_2.9.5_dengler_vds_export.png|600px]] | [[image:vts_2.9.5_dengler_vds_export.png|600px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | |||
| + | |||
| + | ==[[image:Check.jpg|25px]]NEW - MINIMUM CLAMP LENGTH== | ||
| + | |||
| + | <table cellpadding=10 width=900> | ||
| + | <tr valign=top> | ||
| + | |||
| + | <td width=400> | ||
| + | VTube has a new Minimum Clamp Length field in the Part Setup menu.<br><br> | ||
| + | If any bender data length is shorter than the minimum clamp length, then VTube will now issue a warning in the header above the viewport. | ||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:vts_2.9.5_minimum_clamp_length.png|600px]]<br><br> | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | ==[[image:Check.jpg|25px]]NEW - ZERO-DEGREE BEND ANGLE WARNING== | ||
| + | |||
| + | <table cellpadding=10 width=900> | ||
| + | <tr valign=top> | ||
| + | |||
| + | <td width=400> | ||
| + | If any bend angle is less than 0.1 degrees, VTube will now issue a "Zero-degree bend" warning in the header above the viewport. | ||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:vts_2.9.5_zero-degree_bend.png|600px]]<br><br> | ||
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 00:03, 14 March 2018
|
Revision 2.9.5Release Date: March 2, 2018
|
|
ENHANCED - FASTER USER INTERFACE
|
VTube is now faster due to some important changes to the user interface. |
|
FIX - SOLID MODEL IMAGE PRINT IN REPORTS
|
VTube is designed to handle multiple displays. |
|
NEW - SEPARATE PERSPECTIVE MODES FOR STEP and LASER WINDOWS
|
In previous versions, there was only a single Perspective Mode switch. |
|
NEW - REQUEST REVERSE CALC WHEN EXITING THE LRA GRIDS
|
When you edit the data in the LRA grid, VTube-LASER now assumes that you probably mean to perform a reverse calc. |
|
FIX - REPAIRED LOSS OF ORIGINAL ORIENTATION DURING REVERSE CALC
|
VTube always attempts to keep the original XYZ orientation when you perform a Reverse Calc from LRA to centerline XYZ data. |
|
FIX - BUILD TO TUBE TO SOLIDWORKS
|
VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly. |
|
NEW - BEND-TECH 7X IMPORT
|
Now VTube can import the new BEND-TECH 7x format as well as the older version 6 format. |
|
NEW - DENGLER VDS IMPORT (XYZ Data)
|
VTube can now import DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.) |
|
NEW - DENGLER VDS EXPORT(XYZ Data)
|
VTube can now export DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.) |
|
NEW - MINIMUM CLAMP LENGTH
|
VTube has a new Minimum Clamp Length field in the Part Setup menu. |
|
NEW - ZERO-DEGREE BEND ANGLE WARNING
|
If any bend angle is less than 0.1 degrees, VTube will now issue a "Zero-degree bend" warning in the header above the viewport. |
|
Other Pages
- See VTube-LASER Addata ZModem Communications Protocol for more information.
- Back to VTube-LASER
- Back to VTube Software Updates (for LASER Mode)
- See also VTube-STEP
- See also VTube-STEP Revisions
- See VTube-LASER Customer Support Page to download the latest version.
- See the tutorial on DCF - Dual Cylinder Fit
- See the tutorial on DCP - Diameter Cut Planes
- See VTube-LASER Cut Planes
- See How to Measure Tubes Attached to an Evaporator with the DCP Feature
