Difference between revisions of "VTube-LASER v1.73"

From ATTWiki
Jump to: navigation, search
(25px Other Changes)
(Other Pages)
 
(3 intermediate revisions by one user not shown)
Line 89: Line 89:
 
<td width=300>
 
<td width=300>
 
* A graphics model memory leak was repaired where project files continued to grow in size every save and load. This change makes loading and saving much faster in VTube.<br><br>
 
* A graphics model memory leak was repaired where project files continued to grow in size every save and load. This change makes loading and saving much faster in VTube.<br><br>
* The Split Bend logic was enhanced and Split Bend envelopes were enhanced.<br><br>
+
* The Split Bend math logic was improved.<br><br>
 
* New confirmation menus for when pressing STOP or CLEAR the measure process.  This prevents accidentally canceling measuring processes.<br><br>
 
* New confirmation menus for when pressing STOP or CLEAR the measure process.  This prevents accidentally canceling measuring processes.<br><br>
 
</td>
 
</td>
Line 96: Line 96:
 
</tr>
 
</tr>
 
</table>
 
</table>
 
===[[image:Check.jpg|25px]] Issues with this version fixed in newer versions===
 
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=500>
 
* No known issues</td>
 
<td width=300>
 
</td>
 
</tr>
 
</table>
 
 
<br><br>
 
  
 
=Other Pages=
 
=Other Pages=
 
*Back to [[VTube-LASER]]
 
*Back to [[VTube-LASER]]
 
<table>
 
<tr>
 
<td width="400">
 
[http://www.youtube.com/watch?v=HblLf0BpNgk VTube-LASER Training Video] - How to perform effective end scans.
 
</td>
 
<td>
 
[[image:vtube-laser_effective_end_scan_video_b.jpg|300px]]
 
</td>
 
</tr>
 
</table>
 

Latest revision as of 23:43, 20 October 2011

Vtube-laser logo.jpg

Revision 1.73

Back to VTube-LASER
Back to VTube-STEP

Vtube-laser 1 73.jpg

Contents


Check.jpg ENHANCED: Fine Tune for FARO Edge ScanArm

The FARO Edge uses a different scan rate than the older arms. VTube-LASER was adjusted to work with the FARO Edge arms.

Check.jpg ENHANCED: Cut Plane Offset Reset

The Cut Plane Offset can now be changed without remeasuring the Cut Plane.

Vtube-laser cutplaneoffset changeoffet v1 73.jpg

Check.jpg ENHANCED: Cut Plane Offset Value

The Cut Plane Offset Value is now displayed above the Cut Plane icon.

Vtube-laser cutplaneoffset displayoffet v1 73.jpg

Check.jpg NEW: Split Bend Model Display

New Split Bend model geometry is included on the screen when measuring split bends in order to visually verify the calculations.

Vtube-laser splitbend model geometry.jpg

Check.jpg NEW: XYZ INTERSECTION STRAIGHT LENGTHS

A new chart is included in the inspection report that shows the lengths between intersections for both the MASTER and MEASURED as well as the Delta between the two.

Vtube-laser intersection staight length report.jpg

Check.jpg Other Changes

  • A graphics model memory leak was repaired where project files continued to grow in size every save and load. This change makes loading and saving much faster in VTube.

  • The Split Bend math logic was improved.

  • New confirmation menus for when pressing STOP or CLEAR the measure process. This prevents accidentally canceling measuring processes.

Other Pages