Difference between revisions of "VTube-LASER v1.62"

From ATTWiki
Jump to: navigation, search
(25px FIXED: Import of Diameter and Wall)
(25px Issues with this version fixed in newer versions)
 
(13 intermediate revisions by one user not shown)
Line 7: Line 7:
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
[[image:vtube-laser_1_61.jpg|300px]]
+
[[image:vtube-laser_1_62.jpg|300px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 15: Line 15:
  
  
===[[image:Check.jpg|25px]] ENHANCED: End Scans Faster===
+
===[[image:Check.jpg|25px]] ENHANCED: End Scans Faster + New Progress Window===
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=200>
 
<td width=200>
Analysis of end scans is now much faster.
+
Analysis of end scans is now at least twice as fast as in version 1.61.
 
<br><br>
 
<br><br>
 
When end-scans are taking more time than a few seconds, a progress window will display.<br><br>
 
When end-scans are taking more time than a few seconds, a progress window will display.<br><br>
Line 31: Line 31:
 
<br><br>
 
<br><br>
  
===[[image:Check.jpg|25px]] REPAIR: Diameter and Wall Detection for STEP Mode===
+
===[[image:Check.jpg|25px]] NEW: Scan Rate Types: Timer or Distance===
 +
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=200>
 +
Now all scan rates are determined by either a TIMER or a DISTANCE.
 +
<br><br>
 +
For end-scans, use a timer and set the timer value to 0 milliseconds.<br><br>
 +
For cylinder scans, you can use DISTANCE and set the Cylinder Scan Distance to whatever value is convenient for separation.
 +
</td>
 +
<td width=300>
 +
[[image:vtube-laser_measuresetup_scanrates.jpg|300px]]<br><br>
 +
</td>
 +
</tr>
 +
</table>
  
 +
<br><br>
 +
 +
===[[image:Check.jpg|25px]] NEW: Multiple Point Qualification End Scan===
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 +
<td width=200>
 +
VTube-LASER now uses multiple points to qualify the end-scan.  This gives it better protection against outlier points.<br><br>
 +
A new End-Scan Fit window gives information about how many points were used in the end-trim, and the span of all the point positions.  Higher point counts with lower spans indicate a better data set for end-trim.
 +
</td>
 
<td width=300>
 
<td width=300>
 +
[[image:vtube-laser_endscan_fitwindow.jpg|300px]]<br><br>
 +
</td>
 +
</tr>
 +
</table>
 +
 +
<br><br>
 +
 +
===[[image:Check.jpg|25px]] REPAIR: Diameter and Wall Detection for STEP Mode===
 +
 +
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=200>
 
See [[VTube-STEP v1.62]] for details.</td>
 
See [[VTube-STEP v1.62]] for details.</td>
 
<td width=30>
 
<td width=30>
Line 49: Line 81:
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
 +
* The A End and B End OFFSETs other than ZERO caused a problem where end-scans would never be qualified.  This has been resolved in this version.
 
</td>
 
</td>
 
<td>
 
<td>
Line 57: Line 90:
 
<br><br>
 
<br><br>
  
===[[image:Check.jpg|25px]] Issues with this version fixed in next version===
+
===[[image:Check.jpg|25px]] Issues with this version fixed in newer versions===
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=500>
 
<td width=500>
* No known issues</td>
+
*Diameter measures now use the Cylinder scan rate filter setup values. (Fixed in [[VTube-LASER v1.63]])<br><br>
 +
</td>
 
<td width=300>
 
<td width=300>
 
</td>
 
</td>
Line 70: Line 104:
 
=Other Pages=
 
=Other Pages=
 
*Back to [[VTube-LASER]]
 
*Back to [[VTube-LASER]]
 +
 +
<table>
 +
<tr>
 +
<td width="400">
 +
[http://www.youtube.com/watch?v=HblLf0BpNgk VTube-LASER Training Video] - How to perform effective end scans.
 +
</td>
 +
<td>
 +
[[image:vtube-laser_effective_end_scan_video_b.jpg|300px]]
 +
</td>
 +
</tr>
 +
</table>

Latest revision as of 16:54, 1 April 2011

Vtube-laser logo.jpg

Revision 1.62

Back to VTube-LASER

Vtube-laser 1 62.jpg



Check.jpg ENHANCED: End Scans Faster + New Progress Window

Analysis of end scans is now at least twice as fast as in version 1.61.

When end-scans are taking more time than a few seconds, a progress window will display.

Vtube-laser endscan progresswindow.jpg



Check.jpg NEW: Scan Rate Types: Timer or Distance

Now all scan rates are determined by either a TIMER or a DISTANCE.

For end-scans, use a timer and set the timer value to 0 milliseconds.

For cylinder scans, you can use DISTANCE and set the Cylinder Scan Distance to whatever value is convenient for separation.

Vtube-laser measuresetup scanrates.jpg



Check.jpg NEW: Multiple Point Qualification End Scan

VTube-LASER now uses multiple points to qualify the end-scan. This gives it better protection against outlier points.

A new End-Scan Fit window gives information about how many points were used in the end-trim, and the span of all the point positions. Higher point counts with lower spans indicate a better data set for end-trim.

Vtube-laser endscan fitwindow.jpg



Check.jpg REPAIR: Diameter and Wall Detection for STEP Mode

See VTube-STEP v1.62 for details.

Vtube-step 1 62.jpg



Check.jpg Other Changes

  • The A End and B End OFFSETs other than ZERO caused a problem where end-scans would never be qualified. This has been resolved in this version.



Check.jpg Issues with this version fixed in newer versions

  • Diameter measures now use the Cylinder scan rate filter setup values. (Fixed in VTube-LASER v1.63)

Other Pages

VTube-LASER Training Video - How to perform effective end scans.

Vtube-laser effective end scan video b.jpg