Difference between revisions of "VTube-LASER v1.56"

From ATTWiki
Jump to: navigation, search
(25px ENHANCED - New Fields in the Reports)
(25px ENHANCED - New Fields in the Reports)
Line 83: Line 83:
 
===[[image:Check.jpg|25px]] ENHANCED - New Fields in the Reports  ===
 
===[[image:Check.jpg|25px]] ENHANCED - New Fields in the Reports  ===
  
The reports have fields added - like "comments", and "wall".<br><br>
+
The reports have fields added - like "comments", and "wall".<br>
 
[[image:vtube-laser_v1_56_reportfirstpage.jpg|500px]]
 
[[image:vtube-laser_v1_56_reportfirstpage.jpg|500px]]
<br><br>
+
<br>
A requested XYZ deviation chart can now be programmed into the reports:<br>
+
An XYZ deviation chart can now be programmed into the reports:<br>
 
[[image:vtube-laser_v1_56_reportxyzdev.jpg|500px]]
 
[[image:vtube-laser_v1_56_reportxyzdev.jpg|500px]]
  

Revision as of 02:46, 7 January 2011

Vtube-laser logo.jpg

Revision 1.56

Back to VTube-LASER

Vtube-laser screen 1 56.jpg


Check.jpg NEW: Springback Compensation

VTube now uses standard springback-compensation variables in the Part Setup menu. Here are some points about the feature:

  • The fixed springback value is a degree value added to every bend.

  • The proportional springback value is a percentage multiplied against every bend.

  • The values are used to anticipate springback of material in bending and compensate by over bending if necessary during correction.
  • The values are always used automatically in the Bender Setup menu. (See below for more details).

Vtube-laser 1 56 part setup springback.jpg

  • If the values are ZERO, then they are effectively switched off.

  • The values can be calculated using the Advanced Tubular Technologies Overbend Calculator.



Check.jpg ENHANCED - Bender Setup Menu With Springback Values

The Bender Setup menu now includes columns for springback adjustment calculations where you can view how much the part is changed by the springback values.

These values are automatically calculated in this menu from the Part Setup "Fixed" and "Proportional" Springback values.

Vtube-laser 1 56 bendersetupmenu closeup.jpg

Check.jpg ENHANCED - Bender Setup Menu Column Color Changes

The Bender Setup menu shows color columns for any column with data that can be edited on the fly.

Gray columns are not editable in the grid.

Vtube-laser 1 56 bendersetupmenu closeup columns.jpg

Vtube-laser 1 56 bendersetupmenu.jpg


Check.jpg ENHANCED - Bender Setup Menu Popup Menu for Rotations

Sometimes the corrected rotation value may move in the wrong direction.

The Bender Setup menu has new popup menus for the rotation and rotation adjust cells that allow you to quickly invert the rotation to change the rotation directions (to help in bender setup).

Vtube-laser 1 56 bendersetupmenu closeup rotation invert.jpg

Check.jpg ENHANCED - New Fields in the Reports

The reports have fields added - like "comments", and "wall".
Vtube-laser v1 56 reportfirstpage.jpg
An XYZ deviation chart can now be programmed into the reports:
Vtube-laser v1 56 reportxyzdev.jpg

Check.jpg FIX - Measure Tube XYZ Data Build

This version fixes a bug found in version 1.54 where the Measured XYZ data may not update after a measure.

Please be sure to use this version rather than v1.54.

Check.jpg ENHANCED - Best Fit Alignment Mathematics

New features were added to prevent unnecessary errors/warnings from displaying for parts that align too closely with the master part.

Other Pages