Difference between revisions of "VTube-LASER Videos for FARO"

From ATTWiki
Jump to: navigation, search
(Video 20210622: Get Great End Scans Using Flier Filters in VTube-LASER)
(Version 3.2)
 
(13 intermediate revisions by one user not shown)
Line 5: Line 5:
 
See a complete list of VTube-LASER videos on this page.<br><br>
 
See a complete list of VTube-LASER videos on this page.<br><br>
  
* Back to [[VTube-LASER]] Knowledgebase Page<br><br>
+
* Back to [[VTube-LASER]] Knowledgebase Page<br>
 +
* Back to the [[VTube-LASER Videos]] Page<br><br>
 
* Note: VTube-STEP is included with every VTube-LASER installation.  You can watch '''VTube-STEP videos''' in the [[VTube-STEP Videos]] page.
 
* Note: VTube-STEP is included with every VTube-LASER installation.  You can watch '''VTube-STEP videos''' in the [[VTube-STEP Videos]] page.
 
* See [[Retired VTube-LASER Videos]]
 
* See [[Retired VTube-LASER Videos]]
Line 19: Line 20:
  
  
 +
 +
===Version 3.2===
 +
 +
====Video 20220629: How Set Up to Correct SMI Benders with VTube-LASER====
 +
<table width=700>
 +
<tr>
 +
<td width=300>
 +
This video shows set up VTube-LASER to correct SMI benders.
 +
<td width=200>
 +
[[image:vtl_v3.2_SMIBenderCorrectionVideo.png|300px]]<br>
 +
</td>
 +
<td width=300>
 +
* View [https://www.advancedtubular.com/vtube-laser/20220629_VTube-LASER_SMI_Corrections.mp4 MP4]
 +
</td>
 +
</tr>
 +
</table>
 +
 +
 +
====Video 20220603: How To Measure Square and Rectangular Tubing with VTube-LASER and a FARO ScanArm====
 +
<table width=700>
 +
<tr>
 +
<td width=300>
 +
This video shows how use a FARO Quantum ScanArm to measure square or rectangular tubing.
 +
<td width=200>
 +
[[image:vtl_v3.2_FaroSquareTubingVideo.png|300px]]<br>
 +
</td>
 +
<td width=300>
 +
* View [https://www.advancedtubular.com/vtube-laser/20220603_vtl3.2_SquareTube_FARO.mp4 MP4]
 +
* View [https://vimeo.com/716899246 Vimeo]
 +
* View [https://youtu.be/rhohh9X3bU0 YouTube]
 +
</td>
 +
</tr>
 +
</table>
 +
 +
====Video 20220421: How To Set Up and Test VTube-LASER to CNC Bender ProControl Communications====
 +
<table width=700>
 +
<tr>
 +
<td width=300>
 +
This video shows how to set up and test communications with the SMT CNC Bender ProControl benders.
 +
<td width=200>
 +
[[image:vtl_v3.2b750_CNCBenderBenderlinkVideo.png|300px]]<br>
 +
</td>
 +
<td width=300>
 +
* View [https://www.advancedtubular.com/vtube-laser/20220421_VTube-LASER_to_CNC_Bender_Communications_Setup.mp4 MP4]
 +
</td>
 +
</tr>
 +
</table>
 +
 +
====Video 20220331: Improved Best Fit For Shallow Bends====
 +
<table width=700>
 +
<tr>
 +
<td width=300>
 +
This video shows how this version of VTube-LASER has an improved Best Fit algorithm designed to handle tubes with shallow bends.
 +
<td width=200>
 +
[[image:vtl_v3.2b714_BestFitShallowBend.png|300px]]<br>
 +
</td>
 +
<td width=300>
 +
* View [https://www.advancedtubular.com/vtube-laser/20220331_v3.2_b714_BestFitShallowBendLogic.mp4 MP4]
 +
* View [https://vimeo.com/694643426 Vimeo]
 +
</td>
 +
</tr>
 +
</table>
 +
 +
===Version 3.1===
 +
 +
====Video 20220113: How to Calculate VTube-LASER Tube Elongation Percentage====
 +
<table width=700>
 +
<tr>
 +
<td width=300>
 +
This video shows how to calculate tube elongation percentage with VTube-LASER.
 +
 +
<td width=200>
 +
[[image:20220113_Video.png|300px]]<br>
 +
</td>
 +
<td width=300>
 +
* View [https://www.advancedtubular.com/vtube-laser/vtl_v3.1_training%20video%2015%20-%20How%20to%20Calculate%20the%20Tube%20Elongation%20Percentage.mp4 MP4]
 +
* View [https://vimeo.com/665826780 Vimeo]
 +
* View [https://youtu.be/a0bc6IpbWb0  YouTube]
 +
 +
</td>
 +
</tr>
 +
 +
</table>
  
 
===Version 3.0===
 
===Version 3.0===
 +
 +
====Video 20210702: How To Enter Tangent Points to Define the Centerline in VTube====
 +
<table width=700>
 +
<tr>
 +
<td width=300>
 +
Michael Cone explains how the new Tangent Point Entry Grid feature allows operators to enter tangent-point-based centerline data in VTube-STEP and VTube-LASER.(Version 3 build 555, July 2, 2021)
 +
 +
<td width=200>
 +
[[image:20210702_TangentPointEntryGrid.png|300px]]<br>
 +
</td>
 +
<td width=300>
 +
* View [https://www.advancedtubular.com/vtube-laser/vtl_v3_b555_tangent_point_entry_grid.mp4 MP4]
 +
* View [https://vimeo.com/571874446 Vimeo]
 +
* View [https://youtu.be/C9yLbhoWlSE  YouTube]
 +
 +
</td>
 +
</tr>
 +
 +
</table>
  
  

Latest revision as of 16:19, 29 June 2022

See a complete list of VTube-LASER videos on this page.

Vtube-laser video FARO.png




Version 3.2

Video 20220629: How Set Up to Correct SMI Benders with VTube-LASER

This video shows set up VTube-LASER to correct SMI benders.

Vtl v3.2 SMIBenderCorrectionVideo.png


Video 20220603: How To Measure Square and Rectangular Tubing with VTube-LASER and a FARO ScanArm

This video shows how use a FARO Quantum ScanArm to measure square or rectangular tubing.

Vtl v3.2 FaroSquareTubingVideo.png

Video 20220421: How To Set Up and Test VTube-LASER to CNC Bender ProControl Communications

This video shows how to set up and test communications with the SMT CNC Bender ProControl benders.

Vtl v3.2b750 CNCBenderBenderlinkVideo.png

Video 20220331: Improved Best Fit For Shallow Bends

This video shows how this version of VTube-LASER has an improved Best Fit algorithm designed to handle tubes with shallow bends.

Vtl v3.2b714 BestFitShallowBend.png

Version 3.1

Video 20220113: How to Calculate VTube-LASER Tube Elongation Percentage

This video shows how to calculate tube elongation percentage with VTube-LASER.

20220113 Video.png

Version 3.0

Video 20210702: How To Enter Tangent Points to Define the Centerline in VTube

Michael Cone explains how the new Tangent Point Entry Grid feature allows operators to enter tangent-point-based centerline data in VTube-STEP and VTube-LASER.(Version 3 build 555, July 2, 2021)

20210702 TangentPointEntryGrid.png


Video 20210622: Get Great End Scans Using Flier Filters in VTube-LASER

Michael Cone explains the End Scan Flier Filter feature that automatically removes fliers from end scans. (Version 3 build 542, June 22, 2021)

20210622 End Scan Flier Filter Promo.png



Video 20210505: How To Determine Positive and Negative Rotation Directions

Michael Cone explains how to determine if the rotation direction on your CNC bender matches the rotation direction in VTube.

20210505 Positive Rotation Direction.png



Video 20210503: Automatic Reverse Calc

Michael Cone explains the new Automatic Reverse Calc in VTube version 3 build 513.

20210503 AutomaticReverseCalcVideo.png




Video 202100413: VTube v3 NPS Values Tutorial

Michael Cone shows how to use the new NPS values in VTube.

20210413 NPSVideo.png



Video 20210330: VTube-LASER to Transfluid Bender Communications

This video shows how easy it is to communicate with Transfluid tProject bender software.

20210330 TransfluidTProjectCommunications.png



Video 20210313: How to Enter Bender Data of Different Types in the Same Project

This video shows how to enter bender data of mixed data types and then reverse calc to centerline XYZ data.

20210313 ImportMixedBenderData.png




Video 20210310: How to Import New Report Templates

This video shows how to import new report templates into VTube-STEP and VTube-LASER.

20210310 ImportReportTemplates.png



Video 20210212: Switch the FARO Scanner ON and OFF Manually

Use this process to quickly switch the FARO scanner on or off manually.

20210212 FARO Scanner ONOFF.png



Video 20201117: Calculate Centerline Radii Using Measure Bend Profile (FARO)

Quickly and accurately measure the centerline radius using the Measure Bend Profile process.

20201117 measurebendprofile bendradii.png




Video 20201111B: Automatic Copy of the Default Tolerance to Tube Straights

Learn how automatically copy the edited default tangent/midpoint tolerance to all the tube straights.

20201111B autocopydefaulttolerance.png



Video 20201111: How to Use Precision Weight Control Alignment to Simulate Zero-Tolerance Gauges

Learn how to use Precision Weight Control Alignment in VTube-LASER to better simulate zero-tolerance gauges.

20201111 precisionweightcontrolalignment.png




Video 20200923: How to Measure and Qualify Ports on a Tube Using Assembly (FARO)

This video shows how to use Assembly to measure and qualify ports attached to a tube using VTube-LASER Assembly. The same principle can be extended to holes in tube shapes.

20200923 measureing tubes with ports.png



Video 20200609: How to Use Multiple Versions of the Same Part in One Project

This video shows how to use Assembly to create multiple versions of the same part in one project. Each version can then be used to measure the part at various stages of the fabrication process.

20200609 multiple versions parts video.png



Video 20200804: Measuring a Brake Line with a FARO EDGE Arm

This video shows VTube-LASER measuring a brake line with a legacy FARO Edge Scan Arm.

2020804 Brake Line FAROEdge.png



Video 20200515: How Import 180-degree Bend Models

This video shows how to import models with 180-degree bends.

20200515 import180 video.png



Video 20200514: How to Change Languages in VTube

This video shows how to change languages in the VTube-LASER and VTube-STEP user interface.

20200514 changelanguges video.png



Video 20200406: Measure Corner Profile with VTube-LASER and FARO Quantum

This video shows how to measure a corner profile shape with the Corner Profile measure process using a FARO Quantum arm.

20200406 cornerprofile faro video.png



Video 20200327: VTube UNIVERSITY Training Video: Introduction to Import and Measuring Tube Shape Demo Tube 5 with a FARO Arm

(FARO QUANTUM S ScanArm)

This video is a VTube University video designed to accompany training document 20200327..002" this support page.

20200327 trainingdoc002 video.png



Video 20200323: VTube UNIVERSITY Training Video: FARO Account Manager Demo Training

(FARO QUANTUM S ScanArm)

This video is a VTube University video designed to show how to demonstrate VTube-LASER using a FARO ScanArm.

This video is a supplement to the demo training document available on this support page.

Vtl v3.0 training faro demonstration.png



Version 2.9.21

Video 20200204: How to Measure a Bend Radius with Bend Profile Process

See how to use VTube-LASER Bend Profile measure process to measure a bend radius.

(Using a FARO Quantum ScanArm)

Vtl v2.9.21 bendprofilescan faroquantum.mp4.png



Video 107: Corrections Loop with SOCO Beckhoff Controls

This demo video shows how VTube-LASER performs corrections loop communications with SOCO Beckhoff controls.

Vtubelaser v2.9.21.video soco beckhoff communications.png



Version 2.9.18

Video 100: How To Calculate the Centerline Radius in a Measured 180-degree Bend

This video shows how to use the Dimension Control window to calculate the true radius of a 180-degree bend.

Vtubestep v2.9.18.video calculate true radius 180-degree.png




Video 98: About the Small Diameter Warning

This video shows how Small Diameter Warning works along with its setup.

Vtubestep v2.9.18.video small diameter warning.png



Video 96: VTube-STEP and VTube-LASER New Radius Features

See the new radius features in this video. In Part Setup:

  • Renamed "Radius 1" (renamed from Default Radius)
  • New "Radius 2" field
  • New "Radius 3" field


In Parametric Tube grid windows:

  • See how to quickly set the radii for all bends using the synchronize radius feature.

Vtube v2.9.18.video newradius features.png



Version 2.9.17

Video 93: Five Major Enhancements to VTube-LASER Version 2.9.17 - Using a FARO ScanArm

Michael Cone shows 5 major new features in VTube-LASER v2.9.17. (Released on December 30, 2018).

Vtl v2.9.17.video newfeatures faro demo.png



Video 91: How To Reverse-Engineer to STEP file with a FARO ScanArm Using VTube-LASER

This video shows how to reverse-engineer a tube to STEP file. Michael Cone is using VTube-LASER 2.9.17 and a FARO Quantum S ScanArm.

Vtl v2.9.17.video reverse faro.png



Version 2.9.11

Video 87: VTube-LASER's IMPROVED SQUARE TUBE SCANNING (FARO)

This video shows the improved square-tube scanning feature in version 2.9.11 using a FARO ScanArm.

Vtl v2.9.11 squaretubescanningfaro video.png



Version 2.9.9

Video 83: How to Use VTube-STEP and VTube-LASER to Setup and Correct a UNISON Bender

This video shows how to use VTube to setup and correct a Unison bender from model through finished part.

Vvtl 2.9.9 setup and correct a unison bender video.png


Version 2

Video 75: HOW TO USE ASSEMBLY CONTROL

This video demonstrates the new ASSEMBLY CONTROL feature in version 2.9 of VTube-LASER. This feature allows you to import, measure, and align ANY number of tubes in one project.

Vtube-laser v2.9 assembly video.png


Video 74: HOW TO CONNECT VTUBE-LASER TO A FARO ARM

This video shows how to connect to the FARO arm and access the FARO driver windows from inside VTube-LASER.

Vtube-laser v2.9 connect to faro video.png


Video 73: MEASURING TUBE WITH ARMOR

Michael Cone shows how to setup VTube-LASER to measure tube with armor on the OD.

Vtube-laser v2.9 tutorial tubearmor video.png



Video 72: VTUBE-LASER CORRECTING AN AIM WIRE BENDER

This video was created by AIM MACHINES. It shows a user correcting a wire bender with the FARO arm using our VTube-LASER software.

VTube-LASER AIM Wire Bender Video.png


Video 71: HOW TO COMPARE SOLID MODELS TO PRINT DATA

This is a tutorial that shows how to compare solid models to print data to determine if they are the same part.

Vtube-laser v2.9 compare models to print video.png


Video 70: PROPER END-SCAN TECHNIQUE

This is a tutorial that shows how to properly perform an end-scan with VTube-LASER. Follow these simple techniques to ensure that your end scans are reliable and accurate.

Vtube-laser v2.9 endscan tutorial video.png


Video 69: PATH MANAGER SEARCH AND MOVE

The PATH MANAGER is window that contains a list of paths that you want to access often in VTube-LASER.

This video shows how the new SEARCH and MOVE feature works in the PATH MANAGER.

Vtube-laser v2.8.5 pathmanager searchandmove video.png


Video 68: RECALLING and SENDING DATA with ADDATA ZMODEM PROTOCOL

This is a 21-second video showing VTube-LASER communicating with a bender using the Addata ZModem protocol.

First, do a RECALL to update BLUE bender data columns from the bender. Second, SEND the ORANGE columns with corrected data to the bender.

Vtube-laser v2.8.3 AddataZModem Video.png


Video 67: When to use UNISCAN and MULTISCAN Scanning Modes in VTube-LASER

This video demonstrates how and why to switch from UNISCAN to MULTISCAN scanning modes and back.

Vtube-laser v2.8.1 uniscan multiscan demo video.png


Video 66: VTube-LASER Speed Test - LOAD PROJECT - SCAN - REPORT

This is a speed test on a 3 bend exhaust part. The goal is show how easy it is to load a project and scan it in order to get a report.

Vtube-laser v2.8 speedtest load-scan-report-video.png


Video 65: Introducton to the PRECISION WEIGHT CONTROL Alignment

Precision Weight Control Alignment allows you to take-over the weighting of every straight section in a VTube-LASER tube. See how the feature works in this video.

Vtube-laser v2.8 pwc alignment video.png


Video 64: Introduction to the DUAL CYLINDER FIT Feature for Scanning

This video shows why the Dual Cylinder Fit feature is a ground-breaking addition to VTube-LASER. If you scan tube shapes, then you should upgrade to this version of VTube-LASER immediately. Watch the video to see why.

Vtube-laser v2.8 dualcylinderfit intro video.png



Video 63: Quick Demo of ORBIT Control Window

This is a quick demo of the ORBIT Control window that was released in version 2.8.

Vtube-laser v2.8 orbitcontrolwindow video.png



Video 62: Setup and Correct SOCO Benders with VTube-LASER Communications

Created at Tube Form Solutions, this video demonstrates VTube-LASER being used to setup a SOCO bender from a solid model, then correcting the bend program through a network connection by measuring the tube shape and sending correction data to the bender.

Vtube-laser 2.6 soco communications video.png



Video 61: Setup and Correct Alpine Benders with VTube-LASER Network Communications

Created at Elite Tube & Fabrication, this video demonstrates VTube-LASER being used to setup an Alpine bender from a solid model, then correcting the bend program through a network connection by measuring the tube shape and sending correction data to the bender.

Vtube-laser video correcting alpine bender.png



Video 60: Diameter Cut Plane - Quick Tutorial

Michael Cone explains the concept behind the DCP (Diameter Cut Plane) feature and demonstrates how it works. This is a new innovation added in version 2.6.

DCPtutorialVideo.png



Video 59: Diameter Cut Plane - Quick Demo

This video shows what you can do with the DCP (Diameter Cut Plane) feature added in version 2.6. With DCP, even if the laser stripe is crosses multiple straights at the same time, it finds and keeps the closest one - on-the-fly. It even filters out non-diameter objects that are behind the top diameter.

Vtube-laser v2.6 cutplane video.png



Video 58: Speed Test - Reverse Engineer to SOLIDWORKS in Less than 60 Seconds

This video shows how fast VTube-LASER can reverse engineer a tube and build it in SOLIDWORKS - including BEND PROFILE measurements to measure the radius values. The version of VTube-LASER in this video is 2.5.

Vtube-laser v2.5 speedtest reverse to solidworks video.png



Video 57: How To COMPLETELY Reverse Engineer a Tube with the New BEND PROFILE Feature

This video shows how to measure a bend profile to calculate the true radius during reverse engineering of a tube. The version of VTube-LASER in this video is 2.5.

VTube-LASER BendProfile Reverse Radius video.png



Video 56: How to Manually Setup for Measuring Split Bends from Traditional Part Data (180-Degree Bends)

This video shows how to setup Split Bend for measuring 180-degree bends from parts defined in prints. The version of VTube-LASER in this video is 2.5.

VTube-LASER SplitBendSetup FromPartData video.png



Video 55: How to Use Bender Data to Setup the Master Part

Sometimes it's necessary to setup the master part from bender data rather than the normal solid model import or the manual entry of centerline XYZ coordinates.

This video shows you how to do that. The version of VTube-LASER in this video is 2.5.

VTube-LASER ReverseCalc video.png



Video 54: How to Calibrate the FARO Probes in VTube-LASER

Calibrated FARO probes is a foundational skill that is critical for successful measurements.

This video shows how to calibrate the probes and laser scanners from inside VTube-LASER.

The version of VTube-LASER shown in the video is 2.3.

Vtube calibratingprobes video.png



Video 53: Introductory Training in VTube-LASER Version 2

This video is designed for FARO account managers - but it's also good for customers with new users that need to learn how to use VTube-LASER.

It shows how to use the training/demo document for VTube-LASER for training and for giving demonstrations.

You can download the training document from this page.

The version of VTube-LASER shown in the video is 2.3.

Vtube trainingdocument video.png



Video 51: Changing the Part Shape by Changing Bender Data

See how easy it is to quickly change the part shape by editing the bender data.

The version of VTube-LASER shown in the video is 2.2.

Vtube reversecalc video.png



Video 50: VTube User Interface Scan Sounds

This video shows VTube-LASER User Interface scan sounds.

Sounds are an important part of the user interface in VTube. They are designed to give the operators auditory feed back so that they can keep their eyes focused on the part.

The version of VTube-LASER shown in the video is 2.2.

Vtube-laser-v2.2 video scansounds.png

Video 49: Measuring a Tube Gauge

This video shows how to measure a tube gauge with VTube-LASER.

Vtube-laser v2.2 measure tube gauges video.png

Video 48: Reverse-Engineering Demonstrated

This video shows how to reverse engineer a tube shape with VTube-LASER.

Vtube-step-2.2 reverse-engineer video.png

Video 47: MultiScan Measuring Technique

This video shows the MultiScan measuring technique.

Vtube-laser v2.2 multiscan video.png

Video 46: How to Measure Straights With Brackets And Other Objects

This video shows how to scan around objects on a tube straight.

Vtubelaser v2.2 scanaroundobjects.png

Video 45: How to Measure Previous Straights Again

This video shows how repeat a measurement of previous straights.

It also shows you how to skip ahead for over straights that have already been measured.

Vtube-laser v2.2 video previous straights measures.png

Video 44: Entering LRA Data to Establish the Master Data

This quick video shows how to enter LRA bender data to establish the MASTER data for a part.

We refer to the calculation required as "Reverse Calculation" because it reverses the normal direction of calculation in VTube so that the centerline XYZ data after the LRA data is entered.

Vtube-laser v2.2 video enterLRAData.png

Video 43: Wire-form Measuring - 20-second Import and 16-second Measure

For applications that are time-critical, this video shows how VTube-LASER can import and measure tubes very quickly.

Click on the image to watch a video with timers. The part in this video is a wire-form.

Vtube-laser v2.2 video multiscan speedtest.png

Video 42: How To Use a Solid Model to Build VTube-LASER MASTER Data

Click on the image to see a video on how to build VTube-LASER MASTER data from a solid model

Vtube-laser v2.2 video usemodel for master.png

Video 41: Winton Bender Corrections Loop Video

Click on the image to see a 60 second video on how correction loops work with the Winton RD bender:

Vtube-laser 2.2 winton correction loop video.png

Video 40: Sixty Second SPLIT BEND Feature Demo

It's easy and it's accurate: VTube-LASER measures 180 degree bends using a very accurate and unique SPLIT BEND feature.

This video shows how easy it is to use the feature with the FARO scanner.

Vtube-laser-2.2 splitbend video.png

Video 39: Measuring the Demo Tube 3 Radius With the Ball Probe

Measuring the radius with a ball probe is very consistent if done properly.

This video shows how to measure the radius with a ball probe to determine a good default radius during reverse engineering.

Vtube-laser-2.1 radius measure ballprobe video.png

Video 38: Measuring Demo Part 3 with the HD Scanner on a Table Surface

This is a quick video showing how to measure demo tube 3 on a table surface with the HD scanner.

There is no narration in this video.

Vtube-laser-2.1 demo tube 3 HDscan cutplane video.png

Video 37: Measuring Demo Part 3 with the HD Scanner in a Tube Clamp

This is a quick video showing how to measure demo tube 3 in a tube clamp with the HD scanner.

There is no narration in this video.

Vtube-laser-2.1 demo tube 3 HDscan video.png

Version 1.96

Video 35: The Difference Between End Length Adjustment and End Measured Offsets

This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael explains the difference between the END LENGTH ADJUSTMENT values and the END MEASURED OFFSET values in the Part Setup menus.

Vtl-1.96-endlengthadjust endmeasuredoffset video.png

Video 34: Using Tube Data Storage Menu to Access Historical Data

This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael will show you how use Tube Data Storage to permanently store historical data about every measure made by VTube-LASER.

Vtl-1.96-tubedatastorage video.png

Version 1.94

Video 33: Reverse Engineering a Tube Using the Ball Probe

This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael will show you how you can reverse engineer a tube with a FARO Edge arm and the ball probe.

Vtube-laser-1.94-reverse engineer tactile video.png.png

Video 32: The Benefits if Wide Diameter Scanning

This is a tutorial by the developer of VTube-LASER, Michael Cone. Michael will show you why wide diameter scanning is superior to other forms of scanning tubes.

Vtube-1.94 widediameterscanning video.png

Video 31: How to Reverse-Engineer a Tube

This video shows how to reverse engineer a tube in VTube-LASER 1.94.

The tube used is demo tube number 3. (Filename: "VTube-Laser Demo 3.vtp")

Vtube-1.94 reverse engineering video.png

Video 30: Springback Compensation Tutorial

This video shows how calculate the anticipated bend angle springback and then compensate the bend setup to make the first part shape close to the nominal shape.

Vtube-1.94 springback compensation video.png



Other Pages