VTube-LASER Videos
|
|
|
Version 1.83 - July 29, 2013
Video Topic: Entering Tube Print Data To Establish the Master Data
| This video shows how to enter data from a tube print in order to establish the master part data in VTube-LASER v1.83 |
|
Version 1.82 - June 19, 2013
Video Topic: Measuring with a Ball Probe
| This video shows how to measure a tube with a ball probe in VTube-LASER Version 1.82 |
|
Version 1.81.5 - April 5, 2013
Video Topic: Point Count and Straight Count
| This short video shows the correspondence between centerline point count and straight count. It helps explain where the straight count comes from when you press the "Set to MASTER Count" button. |
|
Version 1.81.4 - March 28, 2013
Video Topic: How to Change Languages
| This short video shows how to change the language in the VTube user interface. |
|
|
Video Topic: How to Use the Language Editor
| How to edit any language for the VTube user interface using the VTube Language Editor or Microsoft Excel. |
|
|
Version 1.81.3 - February 22, 2013
Video Topic: The New Floating DRO (Digital Readout)
|
This video shows a short closeup of the new floating DRO window in VTube-LASER. |
|
|
Version 1.81.1 - February 5, 2013
Video Topic: How to Use Hard Point 321 PLP (Plane-Line-Point)
|
This video shows how to use the 321 PLP method to align a part. It describes reasons to switch to this method of alignment in unusual circumstances. |
|
Version 1.80.1 - December 14, 2012
Video Topic: Repeatability Test for Surface-Coated Aluminum
|
This demonstrates a quick repeatability test of a surface-coated aluminum tube. |
|
Video Topic: Effective End Scans
|
This demonstrates the different end scan techniques for measuring tube. |
|
Version 1.80 - December 8, 2012
Video Topic: Effective highly reflective aluminum scanning
|
This is a proof-of-concept video for a 1/2" highly reflective aluminum tube. The goal is to demonstrate repeatability better than 300 microns. |
|
Version 1.80 - November 23, 2012
|
How to extract a tube centerline of demo part 2 with VTube-STEP version 1.80. Note that this part has a 180 degree bend - which requires special steps for import anc calculation. |
|
Version 1.76.4 - May 15, 2012
|
How to measure a straight tube. |
|
|
How to use Measured tube data to create Master tube data. |
Version 1.76.3 - April 2, 2012
|
How to setup the Scanner Control to measuring tubes with the laser probe. |
Version 1.76 - March 15, 2012
|
Unbending a tube with coping at either end. |
Version 1.75 - February 2012
- View on YouTube - Measuring a small 8mm tube that bends back on itself
- Download MP4 - Measuring a small 8mm tube that bends back on itself
- View on YouTube - Measuring a highly deformed 6 inch tube for hydroforming
- Download MP4 - Measuring a highly deformed 6 inch tube for hydroforming
- View on YouTube - Reverse engineering a highly reflective part with a 180 degree bend
- Download MP4 - Reverse engineering a highly reflective part with a 180 degree bend
- View on YouTube - How to compare two Supravision project files in VTube-LASER
- Download MP4 - How to compare two Supravision project files in VTube-LASER
- View on YouTube - STEP Mode Solid Model Import of Large Diameter Tube
- Download MP4 - STEP Mode Solid Model Import of Large Diameter Tube
- View on YouTube - How to demonstrate VTube-LASER importing a CAD model.
- Download MP4 - How to demonstrate VTube-LASER importing a CAD model.
- View on YouTube - How to demonstrate measuring the VTube-LASER demo tube.
- Download MP4 - How to demonstrate measuring the VTube-LASER demo tube.
Older Versions
- v1.73 Measuring HVAC parts with 180 degree bends
- v1.57 Reverse Engineering a Tube
- v1.57 Recall MASTER Bender Data from Benders
- v1.53 Reverse Engineering SPEED TEST Video
- Measure 1/2" tube
- Start a new 1/4" tube project with master data
Other Pages
- Back to VTube-LASER
