Difference between revisions of "VTube-LASER Videos"
(→Version 1.80 - December 8, 2012) |
(→Video Topic: Effective highly reflective aluminum scannning) |
||
| Line 31: | Line 31: | ||
This is a proof-of-concept video for a 1/2" highly reflective aluminum tube. The goal is demonstrate repeatability better than 300 microns.<br><br> | This is a proof-of-concept video for a 1/2" highly reflective aluminum tube. The goal is demonstrate repeatability better than 300 microns.<br><br> | ||
The result was a range from 80 to 180 microns (0.003 to 0.007") maximum deviation.<br><br> | The result was a range from 80 to 180 microns (0.003 to 0.007") maximum deviation.<br><br> | ||
| − | This video shows the best way to scan a highly reflective tube end - and how to be sure the scan is good. | + | This video also shows the best way to scan a highly reflective tube end - and how to be sure the scan is good. |
</td> | </td> | ||
<td width=200> | <td width=200> | ||
Revision as of 20:29, 10 December 2012
|
|
|
Version 1.80 - December 8, 2012
Video Topic: Effective highly reflective aluminum scannning
|
This is a proof-of-concept video for a 1/2" highly reflective aluminum tube. The goal is demonstrate repeatability better than 300 microns. |
|
Version 1.80 - November 23, 2012
|
How to extract a tube centerline of demo part 2 with VTube-STEP version 1.80. Note that this part has a 180 degree bend - which requires special steps for import anc calculation. |
|
Version 1.76.4 - May 15, 2012
|
How to measure a straight tube. |
|
|
How to use Measured tube data to create Master tube data. |
Version 1.76.3 - April 2, 2012
|
How to setup the Scanner Control to measuring tubes with the laser probe. |
Version 1.76 - March 15, 2012
|
Unbending a tube with coping at either end. |
Version 1.75 - February 2012
- View on YouTube - Measuring a small 8mm tube that bends back on itself
- Download MP4 - Measuring a small 8mm tube that bends back on itself
- View on YouTube - Measuring a highly deformed 6 inch tube for hydroforming
- Download MP4 - Measuring a highly deformed 6 inch tube for hydroforming
- View on YouTube - Reverse engineering a highly reflective part with a 180 degree bend
- Download MP4 - Reverse engineering a highly reflective part with a 180 degree bend
- View on YouTube - How to compare two Supravision project files in VTube-LASER
- Download MP4 - How to compare two Supravision project files in VTube-LASER
- View on YouTube - STEP Mode Solid Model Import of Large Diameter Tube
- Download MP4 - STEP Mode Solid Model Import of Large Diameter Tube
- View on YouTube - How to demonstrate VTube-LASER importing a CAD model.
- Download MP4 - How to demonstrate VTube-LASER importing a CAD model.
- View on YouTube - How to demonstrate measuring the VTube-LASER demo tube.
- Download MP4 - How to demonstrate measuring the VTube-LASER demo tube.
Older Versions
- v1.73 Measuring HVAC parts with 180 degree bends
- v1.57 Reverse Engineering a Tube
- v1.57 Recall MASTER Bender Data from Benders
- v1.53 Reverse Engineering SPEED TEST Video
- Measure 1/2" tube
- Start a new 1/4" tube project with master data
Other Pages
- Back to VTube-LASER
