Difference between revisions of "VTube-LASER Split Bend Feature"

From ATTWiki
Jump to: navigation, search
(About The Split Bend Feature)
(Why Is Split Bend Necessary?)
Line 36: Line 36:
 
When bend angles reach and exceed 180-degrees, we lose the intersection point between the two adjacent straights.<br><br>
 
When bend angles reach and exceed 180-degrees, we lose the intersection point between the two adjacent straights.<br><br>
 
See the illustration to see why this is the case.<br><br>
 
See the illustration to see why this is the case.<br><br>
When bend angles reach or exceed 180-degrees, then VTube-LASER must form the single bend with two intersection points.<br><br>
+
At 180-degrees or more, then VTube-LASER must form the single bend with two intersection points.<br><br>
 
If any bend as potential to reach and pass 180 degrees, then VTube-LASER must be setup to use the SPLIT BEND method to measure and solve for the centerline formed between the two intersection points in the 180-degree (or greater) bend.
 
If any bend as potential to reach and pass 180 degrees, then VTube-LASER must be setup to use the SPLIT BEND method to measure and solve for the centerline formed between the two intersection points in the 180-degree (or greater) bend.
 
</td>
 
</td>

Revision as of 20:10, 1 May 2017

Vtube-laser logo 1.96.png

Vtl screen hd scanner without logo.png

Contents


About The Split Bend Feature

The Split Bend feature is VTube-LASER's unique method of measuring tubes with 180-degree or greater bends with accuracy.

Vtube-laser v2.2 master with splitbend.png

Why Is Split Bend Necessary?

We invented Split Bend to solve a legacy measuring issue in the tube fabrication.

When bend angles reach and exceed 180-degrees, we lose the intersection point between the two adjacent straights.

See the illustration to see why this is the case.

At 180-degrees or more, then VTube-LASER must form the single bend with two intersection points.

If any bend as potential to reach and pass 180 degrees, then VTube-LASER must be setup to use the SPLIT BEND method to measure and solve for the centerline formed between the two intersection points in the 180-degree (or greater) bend.

Split Bend Progression Image.png

Configuring for Split Bend

Split Bend setup is controlled in the Bend Setup tab of the Master Tube menu in VTube-LASER, and in the Bend Setup tab in VTube-STEP. Both modes of VTube allow you to configure Split Bends.

To turn a Split Bend ON for a straight section, you enter the Split Bend window and select the straights that should be treated as Split Bends.

The Split Bend window is on the Bend Setup tab in the MASTER TUBE menu. Click into that window.

Vtube-laser v2.2 enter split bend window.png

In the Split Bend window, set any straight that will be treated as a Split Bend.

Close the window. VTube will now understand which straight to treat as a Split Bend during measuring.

See Video 54 for how to setup for a Split Bend.

Vtube-laser v2.2 split bend window straight selected.png

Split Bend LRA Compression

VTube-LASER knows that benders still like to refer to the 180-degree bends as a SINGLE bend.

To do handle this, it automatically compresses the LRA data when you turn the SPLIT BEND feature on for any bend.

See the starting data in the top image (before Split Bend is turned on).

Split bend original data.png

For this tube, we turn the Split Bend ON for straights 2 and 4, and the LRA data automatically compresses.

Split bend compressed lra data.png

Split Bend Measuring

During tube measurement, when you arrive at the split bend to scan, VTube-LASER will make a special sound and tell you to scan the OUTSIDE of the bend. Scan as much data as you want - up to 250 stripes. The goal is to be sure that at least one point in one of the stripes touches the highest point of the outside of the bend. So you can take as many stripes of data as you want - VTube will take them all in without a problem.

During scanning, release the green button, and look at the screen. You should see a large area of surfaces that pass the point of the outside of the bend. Press the RED button if you are finished scanning the outside and have not come to 250 stripes.

Now scan the center of the inside. Be sure that at least one point in one stripe passes the center inside of the bend. If you are not sure, then release the green button and look at the screen to see if you have points and surfaces that appear to be in the right place. If you know you've scanned the center, then press the RED button to move on to the next straight.

  • See Video 40 for a quick demo on how to measure a Split Bend.

Split bend measure outside video.png

Vtube-laser-v2.2 measureguide cylindricaltube.png



Other Pages