Difference between revisions of "VTube-LASER Bender Corrections"

From ATTWiki
Jump to: navigation, search
(Correction Damping)
("Bidirectional Communication" - FOR CORRECTIONS)
 
(41 intermediate revisions by one user not shown)
Line 16: Line 16:
 
__TOC__
 
__TOC__
  
 +
==Correcting a Bender==
  
 +
<table>
 +
<tr>
 +
<td width=300>
 +
You can see the deviation in this part.  The transparent yellow tolerance envelopes indicate that the part is outside of the deviation tolerance allowed (in this case 0.039" or 1 mm).<br><br>
 +
VTube-LASER can send correction data to benders to steer them into the correction motion to make the correct tube shape.
 +
</td>
 +
<td>
 +
[[image:vtube-laser_tubemodel_aligned_demo0625.jpg|500px]]
 +
</td>
 +
</tr>
 +
</table>
 +
 +
 +
 +
==BENDER SETUP Window==
  
 
<table cellpadding=10>
 
<table cellpadding=10>
Line 22: Line 38:
 
<td width=300>
 
<td width=300>
  
==Main Screen==
+
VTube-LASER uses the Bender Setup screen to control the values in up to 100 connected benders.<br><br>
VTube-LASER uses the Bender Setup screen to control the values in connected benders.<br><br>
+
 
This screen shows data that is a separate part of VTube memory.  The data in this screen is the bender data, both before and after correction, and it is kept unchanged unless changed by the operator.<br><br>
 
This screen shows data that is a separate part of VTube memory.  The data in this screen is the bender data, both before and after correction, and it is kept unchanged unless changed by the operator.<br><br>
 
+
 
* The blue columns represent the data at the bender before correction.<br><br>
 
* The blue columns represent the data at the bender before correction.<br><br>
 
* The orange columns represent the data at the bender after correction.<br><br>
 
* The orange columns represent the data at the bender after correction.<br><br>
 
* The columns between the blue and orange columns represent the adjustments to the data.
 
* The columns between the blue and orange columns represent the adjustments to the data.
 
+
 
+
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
 +
 
[[image:vtube-laser-bendersetup_screen.jpg|500px]]<br>
 
[[image:vtube-laser-bendersetup_screen.jpg|500px]]<br>
 
[[image:vtube-laser-bendersetup_grid.jpg|500px]]
 
[[image:vtube-laser-bendersetup_grid.jpg|500px]]
 +
 
</td>
 
</td>
 
</tr>  
 
</tr>  
 +
</table>
  
 +
=="Setup the Bender" - FOR SENDING NEW DATA==
 +
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
 +
Use the "SETUP THE BENDER" section on the right to send new data.<br><br>
 +
VTube-LASER can also send setup data to the bender for setup.<br><br>
 +
The software has several choices for controlling how the data is formatted before sending to the bender.
 +
</td>
 +
<td width=300>
 +
[[image:vtube-laser-bendersetup_newdata.jpg|400px]]
 +
</td>
 +
</tr>
 +
</table>
  
==Bidirectional Communication Controls==
+
=="Bidirectional Communication" - FOR CORRECTIONS==
With the right protocol at the bender, VTube-LASER can recall data from the bender, and send both setup and correction data to the bender.<br><br>
+
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=300>
 +
With the right protocol at the bender, VTube-LASER can recall data from the bender, and send both setup and correction data to the bender.<nowiki>*</nowiki><br><br>
 
* Operators typically press the "1" button to recall data to be sure the data in the blue columns match the data in the bender.<br><br>
 
* Operators typically press the "1" button to recall data to be sure the data in the blue columns match the data in the bender.<br><br>
 
* Then they press "2" to send the orange columns to the bender as corrected data.<br><br>
 
* Then they press "2" to send the orange columns to the bender as corrected data.<br><br>
 
* Press "3" to clear the adjustment data after a correction as it should only be used one time.<br><br>
 
* Press "3" to clear the adjustment data after a correction as it should only be used one time.<br><br>
 
* For benders that can't respond to a recall (1 above), they can recalculate the blue columns by clearing and placing the adjustments back into the blue columns automatically.<br><br>
 
* For benders that can't respond to a recall (1 above), they can recalculate the blue columns by clearing and placing the adjustments back into the blue columns automatically.<br><br>
 +
 +
<nowiki>*</nowiki> Not all protocols require a RECALL before sending CORRECTIONS.
  
 
</td>
 
</td>
Line 53: Line 86:
 
</td>
 
</td>
 
</tr>  
 
</tr>  
 +
</table>
  
 +
==Correction Damping==
 +
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
 
+
VTube-LASER uses a unique correction damping feature for situations were corrections tend to over correct.<br><br>
==Correction Damping==
+
We learned the damping algorithm by observing customers make manual adjustments to the correction data before sending the data to the bender.   
VTube-LASER has incorporated a unique correction damping feature into the software for situations were corrections may tend to over correct.<br><br>
+
The damping algorithm was learned by observing corrections in customer applicationsWe can confirm that it works well when needed.
+
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
 
[[image:vtube-laser-bendersetup_damping.jpg|500px]]
 
[[image:vtube-laser-bendersetup_damping.jpg|500px]]
 
</td>
 
</td>
</tr>  
+
</tr>
 
+
 
+
 
</table>
 
</table>
  
 
==Other Pages==
 
==Other Pages==
 +
 +
* See How to [[Setup VTube for Supravision Network Communication]]
 
* Back to [[VTube-LASER]]
 
* Back to [[VTube-LASER]]

Latest revision as of 20:06, 16 July 2018

Vtube-laser logo.jpg

Vtube-laser 1.77.3.jpg


Contents


Correcting a Bender

You can see the deviation in this part. The transparent yellow tolerance envelopes indicate that the part is outside of the deviation tolerance allowed (in this case 0.039" or 1 mm).

VTube-LASER can send correction data to benders to steer them into the correction motion to make the correct tube shape.

Vtube-laser tubemodel aligned demo0625.jpg


BENDER SETUP Window

VTube-LASER uses the Bender Setup screen to control the values in up to 100 connected benders.

This screen shows data that is a separate part of VTube memory. The data in this screen is the bender data, both before and after correction, and it is kept unchanged unless changed by the operator.

  • The blue columns represent the data at the bender before correction.

  • The orange columns represent the data at the bender after correction.

  • The columns between the blue and orange columns represent the adjustments to the data.

Vtube-laser-bendersetup screen.jpg
Vtube-laser-bendersetup grid.jpg

"Setup the Bender" - FOR SENDING NEW DATA

Use the "SETUP THE BENDER" section on the right to send new data.

VTube-LASER can also send setup data to the bender for setup.

The software has several choices for controlling how the data is formatted before sending to the bender.

Vtube-laser-bendersetup newdata.jpg

"Bidirectional Communication" - FOR CORRECTIONS

With the right protocol at the bender, VTube-LASER can recall data from the bender, and send both setup and correction data to the bender.*

  • Operators typically press the "1" button to recall data to be sure the data in the blue columns match the data in the bender.

  • Then they press "2" to send the orange columns to the bender as corrected data.

  • Press "3" to clear the adjustment data after a correction as it should only be used one time.

  • For benders that can't respond to a recall (1 above), they can recalculate the blue columns by clearing and placing the adjustments back into the blue columns automatically.

* Not all protocols require a RECALL before sending CORRECTIONS.

Vtube-laser-bendesetup bidirectional commmunication.jpg

Correction Damping

VTube-LASER uses a unique correction damping feature for situations were corrections tend to over correct.

We learned the damping algorithm by observing customers make manual adjustments to the correction data before sending the data to the bender.

Vtube-laser-bendersetup damping.jpg

Other Pages