Difference between revisions of "CNC Bender v12.7"

From ATTWiki
Jump to: navigation, search
(25px ENHANCED: Load and Start Positions with Bend Arm Motion)
 
(5 intermediate revisions by one user not shown)
Line 2: Line 2:
 
<tr>
 
<tr>
 
<td width=400>
 
<td width=400>
===v12.4 - January 20, 2014===
+
===v12.7 - January 20, 2014===
 
*Back to [[CNC Bender Software Updates]]
 
*Back to [[CNC Bender Software Updates]]
 
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update.
 
*See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update.
Line 16: Line 16:
 
__NOTOC__
 
__NOTOC__
  
==[[image:Check.jpg|25px]] ENHANCED: Load and Start Positions with Bend Arm Motion ==
+
==[[image:Check.jpg|25px]] ENHANCED: Load and Start Positions with Bend Arm Motion Option (in Pre Bend)==
  
  
Line 23: Line 23:
 
<tr>
 
<tr>
 
<td width=400>
 
<td width=400>
CNC Bender PreBend has a new option called "Arm to Home Mode" that controls when the bend arm returns home before bending begins.  The goal is optimization of the cycle.
+
CNC Bender Pre Bend has a new option called "Arm to Home Mode" that controls when the bend arm returns home before bending begins.  The goal is optimization of the cycle.
 
<br><br>
 
<br><br>
 
These are the choices:<br><br>
 
These are the choices:<br><br>
Line 34: Line 34:
 
6: After Move to Start<br><br>
 
6: After Move to Start<br><br>
  
Use this in conjunction with the PostBend Release command where you can turn off the bend arm return during release.</td>
+
Use this in conjunction with the Post Bend Release command where you can turn off the bend arm return during release.</td>
 
<td width=300>
 
<td width=300>
 
[[image:cncbender_ArmToHomeInPrebend.png|500px]]
 
[[image:cncbender_ArmToHomeInPrebend.png|500px]]
Line 52: Line 52:
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
[[image:cncbender_autodieswithoutarm.png|300px]]
+
[[image:cncbender_autodieswithoutarm.png|500px]]
 
</td>
 
</td>
 
<td>
 
<td>
Line 64: Line 64:
 
<tr>
 
<tr>
 
<td width=400>
 
<td width=400>
* The HAND BENDER MODE of CNC Bender is enhanced to allow for Bending without the Feed axis followingThis is helpful for applications where the last bend will pull the chuck into the pressure die or inside wiper die.
+
* New COMDEFs were added to work with the new Arm To Home Mode optionThe commands are:
 +
 
 +
</td>
 +
<td width=300>
 +
[[image:cncbender_armtohome_commands.png]]
 +
</td>
 +
</tr>
 +
</table>
 +
 
 +
<br><br>
 +
 
 +
<table>
 +
<tr>
 +
<td width=400>
 +
* A new help file was added to explain the new Arm to Home Mode option.
 +
 
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
 +
[[image:cncbender_armtohome_help.png]]
 
</td>
 
</td>
 
</tr>
 
</tr>

Latest revision as of 21:09, 1 February 2014

v12.7 - January 20, 2014

Cncv12procontrol withteachmode.jpg


Check.jpg ENHANCED: Load and Start Positions with Bend Arm Motion Option (in Pre Bend)

CNC Bender Pre Bend has a new option called "Arm to Home Mode" that controls when the bend arm returns home before bending begins. The goal is optimization of the cycle.

These are the choices:

1: Before Move to Load
2: During Move to Load
3: After Move to Load
4: After Chuck Close
5: During Move to Start
6: After Move to Start

Use this in conjunction with the Post Bend Release command where you can turn off the bend arm return during release.

Cncbender ArmToHomeInPrebend.png



Check.jpg ENHANCED: Post Bend Release Mode Has a New Mode

A new ninth option is added to the Post Bend Release Modes. This mode can be used with the new Arm to Home Mode to switch off the arm homing at the end of the cycle.

Cncbender autodieswithoutarm.png



Check.jpg Other Changes

  • New COMDEFs were added to work with the new Arm To Home Mode option. The commands are:

Cncbender armtohome commands.png



  • A new help file was added to explain the new Arm to Home Mode option.

Cncbender armtohome help.png



Other Pages