Difference between revisions of "CNC Bender v12.1.1"
From ATTWiki
(→25px NEW: Processor Now Checks to See if Inputs are Internal) |
(→25px Other Changes) |
||
| (23 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
<table> | <table> | ||
<tr> | <tr> | ||
| − | <td width= | + | <td width=400> |
| − | ==v12.1 - August | + | ===v12.1.1 - August 26, 2013=== |
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
| − | + | *See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update. | |
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| Line 13: | Line 13: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | |||
__NOTOC__ | __NOTOC__ | ||
| − | |||
| − | + | ==[[image:Check.jpg|25px]] FIX: FRB Clear Part Fixed == | |
| − | + | ||
| − | + | ||
| − | + | ||
CNC Bender would save parts after a FRB clear by default in the c:\cnc\config folder. This was repaired so that it saves inside the the correct parts folder. | CNC Bender would save parts after a FRB clear by default in the c:\cnc\config folder. This was repaired so that it saves inside the the correct parts folder. | ||
| − | |||
| − | + | ==[[image:Check.jpg|25px]] NEW: Processor Now Checks to See if Inputs are Internal== | |
| − | + | CNC Processor can now check if an input is an internal input that is not connected to a physical input. This is used for setting and reading states inside the Processor without using actual physical I/O. | |
| − | + | ||
| − | + | ==[[image:Check.jpg|25px]] FIX: CNC Bender Benderlink Fix with Laservision== | |
| + | CNC Bender Benderlink would sometimes return an out-of-bounds error after receiving Laservision data. This was related to setting the first straight adjustment value to zero. It has been resolved. | ||
| − | + | ==[[image:Check.jpg|25px]] ENHANCED: CNC Bender Benderlink Can Emulated Hyprex Laservision== | |
| + | CNC Bender Benderlink can emulate the Hyprex Laservision mode which handles 21 characters in the part name rather than 14 characaters.<br><br> | ||
| + | [[image:cncbender_12.1_benderlink_hyprex.png|500px]] | ||
| + | |||
| + | ==[[image:Check.jpg|25px]] Other Changes== | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
| − | |||
| − | |||
| − | |||
<td width=300> | <td width=300> | ||
| − | |||
| − | |||
| − | |||
| − | + | * Forward PDA Outputs are cleared when the operator enters CYCLE HOLD. No other outputs are changed when this event occurs. | |
| − | + | ||
| − | + | ||
| − | + | ||
</td> | </td> | ||
| Line 51: | Line 43: | ||
</table> | </table> | ||
| − | =Other Pages= | + | ==Other Pages== |
*Back to [[CNC Bender]] | *Back to [[CNC Bender]] | ||
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
Latest revision as of 17:52, 28 August 2013
v12.1.1 - August 26, 2013
|
|
FIX: FRB Clear Part Fixed
CNC Bender would save parts after a FRB clear by default in the c:\cnc\config folder. This was repaired so that it saves inside the the correct parts folder.
NEW: Processor Now Checks to See if Inputs are Internal
CNC Processor can now check if an input is an internal input that is not connected to a physical input. This is used for setting and reading states inside the Processor without using actual physical I/O.
FIX: CNC Bender Benderlink Fix with Laservision
CNC Bender Benderlink would sometimes return an out-of-bounds error after receiving Laservision data. This was related to setting the first straight adjustment value to zero. It has been resolved.
ENHANCED: CNC Bender Benderlink Can Emulated Hyprex Laservision
CNC Bender Benderlink can emulate the Hyprex Laservision mode which handles 21 characters in the part name rather than 14 characaters.
Other Changes
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender Customer Service Page for an update.
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
