Difference between revisions of "CNC Bender v12-20120622"

From ATTWiki
Jump to: navigation, search
(25px Repair - Robot Clear Bit Can Be High or Low)
(25px Enhancement - AutoSleep Removed)
 
(7 intermediate revisions by one user not shown)
Line 13: Line 13:
 
</table>
 
</table>
 
__NOTOC__
 
__NOTOC__
 +
 +
 +
===[[image:Check.jpg|25px]] New - Radius Level for LOAD Position in PREBEND===
 +
 +
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=400>
 +
The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part.  These are the five options:<br>
 +
<br>
 +
#Use the Radius from the first FRB Row
 +
#Use Radius level 1
 +
#Use Radius level 2
 +
#Use Radius level 3
 +
#Use Radius level 4
 +
 +
</td>
 +
 +
<td width=300>
 +
 +
</td>
 +
 +
</tr>
 +
</table>
 +
 +
[[image:cncbender_radiuslevel_for_loading.jpg]]
 +
 +
===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND===
 +
 +
<table cellpadding=10>
 +
<tr valign=top>
 +
<td width=400>
 +
A new option allows the horizontal axis to move to a specific position for loading.  This is a two-option feature:<br>
 +
</td>
 +
 +
<td width=300>
 +
</td>
 +
 +
</tr>
 +
</table>
 +
[[image:cncbender_horizontalaxisloadposition.jpg]]
 +
 
===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180===
 
===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180===
  
Line 46: Line 87:
 
</table>
 
</table>
  
 
+
===[[image:Check.jpg|25px]] Enhancement - AutoSleep Removed===
===[[image:Check.jpg|25px]] New - Radius Level for LOAD Position in PREBEND===
+
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=400>
 
<td width=400>
The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part. <br>
+
Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.<br>
 
<br>
 
<br>
#Use the Radius from the first FRB Row
+
Now the CNC Processor runs fast with our without AutoSleep enabled.
#Use Radius level 1
+
#Use Radius level 2
+
#Use Radius level 3
+
#Use Radius level 4
+
 
+
 
</td>
 
</td>
  

Latest revision as of 01:31, 30 June 2012

v12-20120622

Cncv12procontrol withteachmode.jpg


Check.jpg New - Radius Level for LOAD Position in PREBEND

The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part. These are the five options:

  1. Use the Radius from the first FRB Row
  2. Use Radius level 1
  3. Use Radius level 2
  4. Use Radius level 3
  5. Use Radius level 4

Cncbender radiuslevel for loading.jpg

Check.jpg New - Horizontal Axis LOAD Position in PREBEND

A new option allows the horizontal axis to move to a specific position for loading. This is a two-option feature:

Cncbender horizontalaxisloadposition.jpg

Check.jpg Repair - Recovery Mode Rotate Spin 180

The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero. This has been fixed.


Check.jpg Repair - Robot Clear Bit Can Be High or Low

The Robot Clear bit always assumed that the TRUE signal was bit high. But some machines assume the opposite. This has been fixed.

Check.jpg Enhancement - AutoSleep Removed

Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.

Now the CNC Processor runs fast with our without AutoSleep enabled.

Other Pages