Difference between revisions of "CNC Bender v12-20100105"

From ATTWiki
Jump to: navigation, search
(25px NEW - CUSTOM COMMANDS)
(25px NEW - CUSTOM COMMANDS)
Line 76: Line 76:
 
<td width=300>
 
<td width=300>
 
* [[Custom Commands]] store the moves learned during Teach Mode<br><br>
 
* [[Custom Commands]] store the moves learned during Teach Mode<br><br>
* A ''single'' Custom Command can contain any number of simultaneous [[Jog Motion]]s.<br><br>
+
* A ''single'' Custom Command can contain any number of simultaneous [[Jog Motion]]s. In a SINGLE Custom Command, you could teach the bender how to combine any number of axes and actuators into one motion.<br><br>
* In a SINGLE Custom Command, you could teach the bender how to combine any number of axes and actuators into one motion.<br><br>
+
 
* Every BEND stores up to 10 custom commands.  For example, a 5 bend part could have up to 60 additional Custom Commands. (10 in PreBend and 50 for the bends. The last bend's Custom Command is used for PostBend.)<br><br>
 
* Every BEND stores up to 10 custom commands.  For example, a 5 bend part could have up to 60 additional Custom Commands. (10 in PreBend and 50 for the bends. The last bend's Custom Command is used for PostBend.)<br><br>
 
* Each Bend's Custom Command changes how the bender works after that bend when transitioning to the next bend.<br><br>
 
* Each Bend's Custom Command changes how the bender works after that bend when transitioning to the next bend.<br><br>
Line 83: Line 82:
  
 
<br><br>
 
<br><br>
See the "[[Custom Command]]s" page to read more about Custom Commands.
+
<font size=4>See the "[[Custom Command]]s" page to read more about Custom Commands.</font>
  
 
</td>
 
</td>

Revision as of 19:45, 18 January 2010

Cncbender logo.jpg

Type of Upgrade: MAJOR VERSION CHANGE with Teach Mode

The changes in this version take CNC Bender to the next step in setup power: TEACH your bender how to solve problems.

V12mainmenu.jpg

Contents



Check.jpg NEW - TEACH MODE

CNC Bender is ready to LEARN if you're ready to TEACH!

Teach Mode allows you to Jog any axis or actuator into position while CNC Bender "watches" and remembers your move exactly as you performed it. Teach the bender your knowledge for difficult transitions between bends.

The power of Teach Mode shows with its ease-of-use. Actual reactions of new operators prove that this is an easy-to-learn Teach Mode system. (We've been told that our system is one of the easiest to learn and use.) Of course, that translates into time-savings and increased productivity over the long-haul.

  • OVERVIEW of USING TEACH MODE

    • Enable Teach Mode inside the options list for bend 1. (See Screen 1)

    • Power on and Cycle Start the bender

    • Press AUTO mode.

    • Activate the Teach button in the Control Mode bar. (See Screen 2)

    • Load and bend the part

    • After bend 1 is finished, the dies will open, and CNC Bender will enter STEP mode, and display the Teach Mode menu. (See Screen 3)

    • Teach the bender up to 10 Custom Commands - each command can contain any number of simultaneous jog motions. (See Screen 4)

    • Exit the Teach Mode window and finish bending the part.

  • OTHER THINGS TO KNOW

    • Teach in PreBend immediately after you chuck the part and press the run buttons.

    • Control extra moves in PostBend using the final bend's Custom Commands.

    • Three Jog Motion speeds: Fast, Slow, and Fine-tune

    • Absolute values for each axis is shown in the Custom Command Editor in real-time during Teach Mode

    • The distance from goal for each axis is tracked and displayed in real-time during Teach Mode


Screen 1: Enable Teach Mode individually for each bend


Screen 2: New TEACH speed button in the Control Mode bar


Screen 3: Teach Mode activates after a Teach Mode Section was encountered during bending


Screen 4: Custom Command Editor during Teach Mode


Check.jpg NEW - CUSTOM COMMANDS

  • Custom Commands store the moves learned during Teach Mode

  • A single Custom Command can contain any number of simultaneous Jog Motions. In a SINGLE Custom Command, you could teach the bender how to combine any number of axes and actuators into one motion.

  • Every BEND stores up to 10 custom commands. For example, a 5 bend part could have up to 60 additional Custom Commands. (10 in PreBend and 50 for the bends. The last bend's Custom Command is used for PostBend.)

  • Each Bend's Custom Command changes how the bender works after that bend when transitioning to the next bend.

Cncb12frb customcommands button.jpg




See the "Custom Commands" page to read more about Custom Commands.

Screen 1: Select one of the Edit Custom buttons a bend in the FRB page
Screen 2: Custom Commands List Selection


Screen 3: Custom Command Editor





Check.jpg NEW - MAIN MENU

The main menu was completely redesigned to make the menu buttons easier to find quickly.

The new v12 main menu in CNC Bender ProControl



Other Pages