Difference between revisions of "CNC Bender v11-20091229"
From ATTWiki
| (22 intermediate revisions by one user not shown) | |||
| Line 8: | Line 8: | ||
<tr> | <tr> | ||
<td> | <td> | ||
| − | Type of Upgrade: '''Optimization''' | + | Type of Upgrade: '''Optimization''' and '''New Feature''' |
</td> | </td> | ||
<td> | <td> | ||
| − | The changes in this version are designed to make CNC Bender more accurate | + | The changes in this version are designed to make CNC Bender more accurate, run faster, and perform new tasks. |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 24: | Line 24: | ||
__TOC__ | __TOC__ | ||
| + | |||
| + | |||
| + | ===[[image:Check.jpg|25px]] NEW - Tube Mandrel Check and Destroyer Feature=== | ||
| + | <table> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | * CNC Bender can now automatically check for the existence of a broken mandrel after a mandrel extraction.<br><br> | ||
| + | * If the mandrel is broken, then CNC Bender process list logic requires the operator to place the tube in a tube destroyer to crush the tube to prevent it from being used in other machinery in the cell.<br><br> | ||
| + | [[image:tubedestroyer.jpg|300px]] | ||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | [[image:mandrelcheck_actuator.jpg|300px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| Line 30: | Line 47: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | * There were circumstances were motion commands could be issued twice when only one command was necessary.<br><br> | + | * There were circumstances were incremental motion commands could be issued twice when only one command was necessary.<br><br> |
| − | * | + | * This version of CNC Bender removes the potential for double calls to incremental motion commands<br><br> |
</td> | </td> | ||
<td width=300> | <td width=300> | ||
| − | [[image:bendarm_blur_vb150.jpg| | + | [[image:bendarm_blur_vb150.jpg|300px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 43: | Line 60: | ||
<br><br> | <br><br> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] ENHANCE- PreBend Rotate to Start Angle User-Interface Change=== |
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | * | + | * The PreBend ROTATE TO START ANGLE feature is now only available in the PreBend Dynamic Options list<br><br> |
| − | * | + | * This reduces confusion so that the operator knows that the feature is available in a single location.<br><br> |
| − | + | ||
</td> | </td> | ||
| − | <td> | + | <td width=300> |
| − | [[image: | + | [[image:rotatetostart_dynamicoption.jpg|300px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | |||
| + | [[image:prebendcarriagemenu_removed_rotate_to_start.jpg|600px]] | ||
<br><br> | <br><br> | ||
| + | |||
| + | |||
=Other Pages= | =Other Pages= | ||
Latest revision as of 22:29, 30 December 2009
|
|
|
Contents |
NEW - Tube Mandrel Check and Destroyer Feature
|
|
ENHANCE- Updates to CNC Processor to improve motion command logic
|
|
ENHANCE- PreBend Rotate to Start Angle User-Interface Change
|
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Final Feed Clearance
