Difference between revisions of "CNC Bender v10-20071120"

From ATTWiki
Jump to: navigation, search
(Menu: Machine Lube)
(Menu: Machine Lube)
Line 90: Line 90:
 
A value of 1 indicates watch for INPUT after the duration.  A value of 0 indicates only run for the DURATION.
 
A value of 1 indicates watch for INPUT after the duration.  A value of 0 indicates only run for the DURATION.
  
The input name is set in the CIO section of CNCProcessor.cfg:
+
See below for how to set the input name.
  
 +
</td>
 +
 +
</tr>
 +
 +
 +
<tr>
 +
<td bgcolor="#ccc5f5">
 +
<font size=3>CIO Input Name to Watch for Lube Complete</font></td>
 +
<td bgcolor="#cceec2">
 +
The input name is set in the CIO section of CNCProcessor.cfg:
 
<b>
 
<b>
 
[CIO]<br>
 
[CIO]<br>
 
CIO Name of Input Machine Lube Complete=Input_MachineLubeComplete_End<br>
 
CIO Name of Input Machine Lube Complete=Input_MachineLubeComplete_End<br>
 
</b>
 
</b>
 
 
</td>
 
</td>
  
Line 107: Line 116:
 
</ul>
 
</ul>
  
</ul>
 
  
 
<br><br>
 
<br><br>

Revision as of 16:55, 23 November 2007

Cncbender logo.jpg

Contents




CHANGES to CNC BENDER



Check.jpg Redesigned Processor Menu

The CNC Processor menu is redesigned to include 5 new tab menus.

Cncprocessor tabmenus.jpg

Cncbender cncprocessor.jpg



Menu: Incoming Messages

    The INCOMING MESSAGES menu now allows you to show an extended history log:

    Cncbender cncprocessor historylog.jpg




Menu: Machine Lube

    The new MACHINE LUBE tab has new controls and features:

    Cncbender cncprocessor machinelube.jpg

    The machine lube setup is control from the CNCProcessor.cfg file in the c:\cnc\config folder.

    New Feature in Machine Lube Description
    Use Pulse or Constant Output

    This indicator shows how CNC Processor is set to handle the output point for the machine lube. The output can be toggled on and off (pulse) or switched on for the entire period of lube (constant).

    This value is controlled in the Machine Lube section of the CNCProcessor.cfg file:

    [Machine Lube]
    Pulse Machine Lube Pump= 0

    A value of 1 indicates PULSE. A value of 0 indicates CONSTANT. CONSTANT is the default setting.

    Watch for input to indicate lube complete

    This indicator shows how CNC Processor is set to determine if the machine lube is completed. If an input is examined to determine if the machine lube is complete, then CNC Processor will activate the output for the duration entered in the setup, then begin examining the input indicated in the configuration.

    This value is controlled in the Machine Lube section of the CNCProcessor.cfg file:

    [Machine Lube]
    Watch For Machine Lube Complete Input= 1

    A value of 1 indicates watch for INPUT after the duration. A value of 0 indicates only run for the DURATION.

    See below for how to set the input name.

    CIO Input Name to Watch for Lube Complete

    The input name is set in the CIO section of CNCProcessor.cfg: [CIO]
    CIO Name of Input Machine Lube Complete=Input_MachineLubeComplete_End




Check.jpg Changed a Range Error Message for Clarity

A range error message was changed by adding the RADIUS CHANGE information to help users find a solution this problem:


Immediate Message

Range Error - According to the RADIUS CHANGE Interference Zone value in the TOOL page the Cross Slide Would Have Collided With The Pressure Die. If this is not the case, then adjust the RADIUS CHANGE Interference Zone value.


Check.jpg Production Cycle Time Value

The "Complete Cycle Time" is changed to "Production Cycle Time" and now provides the overall time from part to part.




Check.jpg New General Dynamic Option - PD Set Pressure

If this option is enabled, then the PD Set Pressure Output Points are enabled using the new SetPDPressureOutputPoints command.

PD set Pressure Output Points enable.jpg



Check.jpg Changed Terminology

The following terms are changed in CNC Bender user interface:


ORIGINAL NEW
In Low Level
Tangent to Collet Face
In Low Level
Machine Length
In Run Page
Complete Cycle Time
In Run Page
Production Cycle Time





CHANGES to CNC PROCESSOR

Check.jpg Optimized for Win2000 or WinXP

This CNC Processor recognizes the current operating system and optimizes the loop for each operating system.








How to UPGRADE

CNC Bender User Interface for ProControl

If your operator station contains one of the versions listed below, then they can be upgraded through simple self-installation:



See our CNC Bender Upgrade Policy page for details regarding the charges for the upgrade software.


Nav down green.pngDownload the setup file by clicking on this link.
This setup file requires a password to run. Please contact John Esralian for upgrade prices and password information.

For instructions on how to install the file see: How to Install a CNC Bender Upgrade