Difference between revisions of "Ball Probe Setup"

From ATTWiki
Jump to: navigation, search
(Created page with "<table> <tr cellpadding=10> <td width=225> 200px * Back to VTube-STEP * Back to VTube-LASER </td> <td width=300> image:vtl_screen...")
 
 
(8 intermediate revisions by one user not shown)
Line 3: Line 3:
 
<td width=225>
 
<td width=225>
 
[[image:vtube-laser_logo_1.96.png|200px]]
 
[[image:vtube-laser_logo_1.96.png|200px]]
* Back to [[VTube-STEP]]
 
 
* Back to [[VTube-LASER]]
 
* Back to [[VTube-LASER]]
 
</td>
 
</td>
Line 15: Line 14:
  
  
== About the Default Ball Probe Setup==
+
== How to Change the Default Ball Probe Setup==
  
The default ball probe setup is always controlled by the FARO dialogs.  These are windows that can be loaded from VTube-LASER while it is connected to the arm.  To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.
+
The default ball probe setup is always controlled by the FARO drivers and dialogs.  The FARO driver dialog windows can be loaded from inside VTube-LASER while VTube is connected to the arm.  To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.<br><br>
  
 +
'''You must be connected to a FARO arm to perform these steps.'''
 
<table>
 
<table>
  
Line 24: Line 24:
 
<td width=300>
 
<td width=300>
 
===STEP 1===
 
===STEP 1===
(You must be connected to a FARO arm to perform these steps.)
+
 
 
In VTube-LASER click on the Arm Utilities button in the Arm tab inside the Measure Setup menu.</td>
 
In VTube-LASER click on the Arm Utilities button in the Arm tab inside the Measure Setup menu.</td>
 
<td>
 
<td>
Line 33: Line 33:
 
<td width=300>
 
<td width=300>
 
===STEP 2===
 
===STEP 2===
Change the values in VTube to whatever you want them be when you perform a clear. Be sure that no tube data exits in this state, or VTube will clear the data to preset values with a tube.  (Of course, you can do this, if you really meant to.)</td>
+
Press Probe Setup and Calibration.</td>
 
<td>
 
<td>
[[image:vtube-step_v2.2_cleared.png|400px]]
+
[[image:vtube-laser_v2.2_armutilities_dialog_press_probesetup_and_calibration.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
 +
 
===STEP 3===
 
===STEP 3===
Press the System Options button.</td>
+
Select the correct ball probe then press OK.<br><br>
 +
This step will cause the FARO driver to report back to VTube the new probe.  The FARO driver should always remember the last ball probe that you set to "Current Probe" in the pulldown box.  This is true even if you shutdown VTube-LASER and the FARO arm.</td>
 
<td>
 
<td>
[[image:Vtube-STEP_v2.2_toolbar_sys.png|400px]]
+
[[image:vtube-laser_v2.2_faro_compensation_menu.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 50: Line 52:
  
 
===STEP 4===
 
===STEP 4===
Press the Project Setup tab, and then press the Set Project Default State button.</td>
+
Press the Close button in the FARO Arm Utilities window.</td>
 
<td>
 
<td>
[[image:vtube_v2.2_projecttab_saveprojectdefault.png|400px]]
+
[[image:vtube-laser_v2.2_armutilities_dialog_press_close.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 60: Line 62:
  
 
===STEP 5===
 
===STEP 5===
Exit the System Options menu.  VTube will now clear to the new settings.
+
Observe that the new ball probe selection will appear in the Arm grid.
 
</td>
 
</td>
 
<td>
 
<td>
[[image:vtube_v2.2_systemoptions_closemenu.png|400px]]
+
[[image:vtube-laser_2.2_measuresetup_menu_6mmball.png|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 72: Line 74:
 
==Other Pages==
 
==Other Pages==
  
*Back to the [[VTube-STEP]] page
 
 
*Back to the [[VTube-LASER]] page
 
*Back to the [[VTube-LASER]] page

Latest revision as of 17:35, 4 September 2015

Vtube-laser logo 1.96.png

Vtl screen hd scanner without logo.png



How to Change the Default Ball Probe Setup

The default ball probe setup is always controlled by the FARO drivers and dialogs. The FARO driver dialog windows can be loaded from inside VTube-LASER while VTube is connected to the arm. To change the default ball probe, you will need to access the FARO dialog and choose the correct probe.

You must be connected to a FARO arm to perform these steps.

STEP 1

In VTube-LASER click on the Arm Utilities button in the Arm tab inside the Measure Setup menu.

Vtube-laser v2.2 measuresetup arm armutilities.png

STEP 2

Press Probe Setup and Calibration.

Vtube-laser v2.2 armutilities dialog press probesetup and calibration.png

STEP 3

Select the correct ball probe then press OK.

This step will cause the FARO driver to report back to VTube the new probe. The FARO driver should always remember the last ball probe that you set to "Current Probe" in the pulldown box. This is true even if you shutdown VTube-LASER and the FARO arm.

Vtube-laser v2.2 faro compensation menu.png

STEP 4

Press the Close button in the FARO Arm Utilities window.

Vtube-laser v2.2 armutilities dialog press close.png

STEP 5

Observe that the new ball probe selection will appear in the Arm grid.

Vtube-laser 2.2 measuresetup menu 6mmball.png


Other Pages