Difference between revisions of "VTube-LASER v2.9.5"

From ATTWiki
Jump to: navigation, search
(25pxFIX - BUILD TO SOLIDWORKS ASSEMBLY)
(25pxFIX - BUILD TO SOLIDWORKS ASSEMBLY)
Line 126: Line 126:
  
 
<td width=400>
 
<td width=400>
VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS ASSEMBLY.<br><br>Since VTube is building a single tube in SOLIDWORKS the best action is to always build a single part drawing.<br><br>
+
VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly.<br><br>Since VTube is building a single tube in SOLIDWORKS the best action is to always build a single part drawing.<br><br>
 
The build logic has been fixed in this version.<br><br>
 
The build logic has been fixed in this version.<br><br>
 
If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly.
 
If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly.

Revision as of 14:04, 28 February 2018

Vtube-laser logo 1.96.png


Revision 2.9.5

Release Date: February 19, 2018
Build:


Vtube-laser v2.7 screenshot.png

Contents


Check.jpgENHANCED - FASTER USER INTERFACE

VTube is now faster due to some important changes to the user interface.



Check.jpgFIX - SOLID MODEL IMAGE PRINT IN REPORTS

VTube is designed to handle multiple displays.

We discovered that, for windows arrangements where the Windows Desktop is not on the far left monitor, VTube might not print the graphics image properly in reports.

This has been fixed in this version.

Vtl report header.png



Check.jpgNEW - SEPARATE PERSPECTIVE MODES FOR STEP and LASER WINDOWS

In previous versions, there was only a single Perspective Mode switch.

In this version, there is a separate Perspective Mode switch for STEP and LASER windows.

Vtl 2.9.5 perspective.png
Vts 2.9.5 perspective.png




Check.jpgNEW - REQUEST REVERSE CALC WHEN EXITING THE LRA GRIDS

When you edit the data in the LRA grid, VTube-LASER now assumes that you probably mean to perform a reverse calc.

If you exit the grid without a reverse calc, then it will immediately ask if you intended to perform a Reverse Calc - and allow you to choose to calculate the XYZ data.

This is active in both the MASTER and the MEASURED LRA grids.

Vtl 2.9.5 request reverse calc.png





Check.jpgFIX - REPAIRED LOSS OF ORIGINAL ORIENTATION DURING REVERSE CALC

VTube always attempts to keep the original XYZ orientation when you perform a Reverse Calc from LRA to centerline XYZ data.

We discovered that certain situations would cause VTube to lose the orientation during Reverse Calc.

This has been fixed in this version.

Vts 2.9.5 reversecalc loss orientation.png

Vts 2.9.5 reversecalc noloss orientation.png



Check.jpgFIX - BUILD TO SOLIDWORKS ASSEMBLY

VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly.

Since VTube is building a single tube in SOLIDWORKS the best action is to always build a single part drawing.

The build logic has been fixed in this version.

If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly.

Vtl 2.9.5 swtrans.png



Other Pages