Difference between revisions of "CNC Bender v12-20100903"

From ATTWiki
Jump to: navigation, search
(25px ENHANCED - EMBEDDED TUBE SUPPORT in CNC PROCESSOR)
Line 8: Line 8:
 
</tr>
 
</tr>
 
</table>
 
</table>
 
__NOTOC__
 
 
 
 
===[[image:Check.jpg|25px]] NEW - CYCLE HOLD in Custom Commands and in TEACH Mode  ===
 
===[[image:Check.jpg|25px]] NEW - CYCLE HOLD in Custom Commands and in TEACH Mode  ===
 
<table cellpadding=10>
 
<table cellpadding=10>

Revision as of 00:18, 1 September 2010

Cncv12procontrol withteachmode.jpg

Contents

Check.jpg NEW - CYCLE HOLD in Custom Commands and in TEACH Mode

Now CYCLE HOLD anywhere inside a CUSTOM COMMAND either manually entered or taught during TEACH MODE.

Cycle Hold pauses the process perpetually until Cycle Start is pressed.

See also the Cycle Hold button.

Cncbender customcommand cyclehold.jpg

Check.jpg ENHANCED - ENABLE Button for STEP and AUTO Modes

The "REQUIRE ENABLE BUTTON" feature, when active, now also monitors for a switch to AUTO or STEP modes from MANUAL mode

When this feature is enabled, then the ENABLE button must be pressed or a large message will display indicating that the operator must press the ENABLE button

Cncbender pressenable to switch to autostep.jpg

Check.jpg ENHANCED - Vertical Head Shift Tolerance Added

The vertical head shift tolerance allows us to skip motion when an axis is close enough to the final position.

The tolerance value is now present in the Low Level General Options list and is used by the processlist compiler to give the Processor more efficient processlists.

Cncbender vertical head shift tolerance options.jpg


Check.jpg ENHANCED - Added CNC Processor Automatic High Pressure Handling


Hydraulic pressure gauge.jpg

CNC Processor now uses the CIO Name Cross Reference in the Low Level menu to automatically set the high pressure under these two special circumstances:

  • Just before CNC Processor performs a direct axis jog, CNC Processor sets the CIO point for high pressure.

  • When CNC Processor switches from Cycle Hold to Cycle Start, CNC Processor sets the CIO point for high pressure.

CIONamesCrossReference.jpg

Check.jpg ENHANCED - CNC Processor Soft EOT with New Ramp-Down for JOG Speeds

During JOGGING - CNC Processor can check for EOT (end of travel) of an axis before it arrives at the true FAULT EOT. This gives the axis a chance to stop jogging before it arrives at a FAULT position or emergency switch.

Joystick.jpg

This feature now adds JOG SPEED control directly to CNC Processor in order to control how slowly to approach the final soft EOT position for any axis. The setup is adjusted in the c:\cnc\config\axis\main.axislist configuration file.

In the example given here, when the bend arm is more than 5 degrees from the soft EOT, it travels at 10 degrees per second. However, when it reaches within 5 degrees of either EOT, then the speed drops to 0.5 degrees per second.

The following section is extracted from an AXIS configuration file soft EOT section:

  • Enable EOT= 1 or 0
  • Low EOT= (floating point value)
  • High EOT= (floating point value)
  • Jog Speed= (positive floating point value of regular jog speed)
  • Jog Speed Approach EOT= (positive floating point value of ramp-down jog speed)
  • Approach EOT Range= (positive floating point value of the range in which the slower jog speed is enabled)




Example of what to add in each AXIS in the main.axislist file. The value shown here are typical of the BEND axis:

Enable EOT=1
Low EOT=0.75
High EOT=191
Jog Speed=10
Jog Speed Approach EOT=0.5
Approach EOT Range=5

Check.jpg ENHANCED - EMBEDDED TUBE SUPPORT in CNC PROCESSOR

This feature allows CNC Bender's PROCESSOR to control when the tube support is lifted or dropped - and if the drop should be confirmed with an input.

This revision adds the CIO Name of Tube Support Output UP in addition to the Down CIO name.

  • Enable
  • Feed Position for Output Down
  • CIO Name of Tube Support Output Down
  • CIO Name of Tube Support Output Up
  • Feed Position for check Input Down
  • CIO Name of Tube Support Input Down




Cncbender do lowlevel tubesupport2.jpg



Other Pages