Difference between revisions of "VTube-LASER v2.9.5"
(→25pxFIX - BUILD TO SOLIDWORKS ASSEMBLY) |
(→Revision 2.9.5) |
||
(16 intermediate revisions by one user not shown) | |||
Line 6: | Line 6: | ||
==Revision 2.9.5== | ==Revision 2.9.5== | ||
− | Release Date: | + | Release Date: March 2, 2018<br> |
− | Build: | + | Build: 1 |
* Back to [[VTube-LASER]] | * Back to [[VTube-LASER]] | ||
Line 34: | Line 34: | ||
<td> | <td> | ||
+ | [[image:VTL Single Tube with shadow.png|400px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
Line 120: | Line 121: | ||
<br><br> | <br><br> | ||
− | ==[[image:Check.jpg|25px]]FIX - BUILD TO SOLIDWORKS | + | ==[[image:Check.jpg|25px]]FIX - BUILD TO TUBE TO SOLIDWORKS== |
<table cellpadding=10 width=800> | <table cellpadding=10 width=800> | ||
Line 126: | Line 127: | ||
<td width=400> | <td width=400> | ||
− | VTube would incorrectly build single | + | VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly.<br><br>If VTube is building a single tube in SOLIDWORKS the best action is to always build a single part drawing.<br><br> |
− | + | The build logic has been fixed in this version.<br><br> | |
+ | If there are multiple parts in VTube, then VTube will still allow you to choose between building all the parts into one drawing, or building all the parts into a SOLIDWORKS assembly. | ||
</td> | </td> | ||
<td> | <td> | ||
[[image:vtl_2.9.5_swtrans.png|400px]]<br><br> | [[image:vtl_2.9.5_swtrans.png|400px]]<br><br> | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | ==[[image:Check.jpg|25px]]NEW - BEND-TECH 7X IMPORT== | ||
+ | |||
+ | <table cellpadding=10 width=800> | ||
+ | <tr valign=top> | ||
+ | |||
+ | <td width=400> | ||
+ | Now VTube can import the new BEND-TECH 7x format as well as the older version 6 format. | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:vts_2.9.5_bend-tech_7x_import.png|600px]] | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | ==[[image:Check.jpg|25px]]NEW - DENGLER VDS IMPORT (XYZ Data)== | ||
+ | |||
+ | <table cellpadding=10 width=800> | ||
+ | <tr valign=top> | ||
+ | |||
+ | <td width=400> | ||
+ | VTube can now import DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.) | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:vts_2.9.5_dengler_vds_import.png|600px]] | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | |||
+ | ==[[image:Check.jpg|25px]]NEW - DENGLER VDS EXPORT(XYZ Data)== | ||
+ | |||
+ | <table cellpadding=10 width=800> | ||
+ | <tr valign=top> | ||
+ | |||
+ | <td width=400> | ||
+ | VTube can now export DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.) | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:vts_2.9.5_dengler_vds_export.png|600px]] | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | |||
+ | |||
+ | ==[[image:Check.jpg|25px]]NEW - MINIMUM CLAMP LENGTH== | ||
+ | |||
+ | <table cellpadding=10 width=900> | ||
+ | <tr valign=top> | ||
+ | |||
+ | <td width=400> | ||
+ | VTube has a new Minimum Clamp Length field in the Part Setup menu.<br><br> | ||
+ | If any bender data length is shorter than the minimum clamp length, then VTube will now issue a warning in the header above the viewport. | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:vts_2.9.5_minimum_clamp_length.png|600px]]<br><br> | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | ==[[image:Check.jpg|25px]]NEW - ZERO-DEGREE BEND ANGLE WARNING== | ||
+ | |||
+ | <table cellpadding=10 width=900> | ||
+ | <tr valign=top> | ||
+ | |||
+ | <td width=400> | ||
+ | If any bend angle is less than 0.1 degrees, VTube will now issue a "Zero-degree bend" warning in the header above the viewport. | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:vts_2.9.5_zero-degree_bend.png|600px]]<br><br> | ||
</td> | </td> | ||
</tr> | </tr> |
Latest revision as of 00:03, 14 March 2018
Revision 2.9.5Release Date: March 2, 2018
|
ENHANCED - FASTER USER INTERFACE
VTube is now faster due to some important changes to the user interface. |
FIX - SOLID MODEL IMAGE PRINT IN REPORTS
VTube is designed to handle multiple displays. |
NEW - SEPARATE PERSPECTIVE MODES FOR STEP and LASER WINDOWS
In previous versions, there was only a single Perspective Mode switch. |
NEW - REQUEST REVERSE CALC WHEN EXITING THE LRA GRIDS
When you edit the data in the LRA grid, VTube-LASER now assumes that you probably mean to perform a reverse calc. |
FIX - REPAIRED LOSS OF ORIGINAL ORIENTATION DURING REVERSE CALC
VTube always attempts to keep the original XYZ orientation when you perform a Reverse Calc from LRA to centerline XYZ data. |
FIX - BUILD TO TUBE TO SOLIDWORKS
VTube would incorrectly build a single tube to both a single part drawing and a SOLIDWORKS assembly. |
NEW - BEND-TECH 7X IMPORT
Now VTube can import the new BEND-TECH 7x format as well as the older version 6 format. |
NEW - DENGLER VDS IMPORT (XYZ Data)
VTube can now import DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.) |
NEW - DENGLER VDS EXPORT(XYZ Data)
VTube can now export DENGLER VDS files. (DENGLER VDS files contain centerline XYZ coordinates.) |
NEW - MINIMUM CLAMP LENGTH
VTube has a new Minimum Clamp Length field in the Part Setup menu. |
NEW - ZERO-DEGREE BEND ANGLE WARNING
If any bend angle is less than 0.1 degrees, VTube will now issue a "Zero-degree bend" warning in the header above the viewport. |
Other Pages
- See VTube-LASER Addata ZModem Communications Protocol for more information.
- Back to VTube-LASER
- Back to VTube Software Updates (for LASER Mode)
- See also VTube-STEP
- See also VTube-STEP Revisions
- See VTube-LASER Customer Support Page to download the latest version.
- See the tutorial on DCF - Dual Cylinder Fit
- See the tutorial on DCP - Diameter Cut Planes
- See VTube-LASER Cut Planes
- See How to Measure Tubes Attached to an Evaporator with the DCP Feature