Difference between revisions of "CNC Bender v12-20110128"
(7 intermediate revisions by one user not shown) | |||
Line 24: | Line 24: | ||
</td> | </td> | ||
<td> | <td> | ||
− | [[image:comdefeditor_ignorestepmode.jpg| | + | [[image:comdefeditor_ignorestepmode.jpg|400px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
− | ===[[image:Check.jpg|25px]] ENHANCED - | + | ===[[image:Check.jpg|25px]] ENHANCED - Teach Mode Button Can Be Invisible === |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
− | + | Some benders don't need TEACH Mode, so the Teach Mode button can be made invisible by enabling a switch in the low level options list. | |
+ | <br> | ||
+ | [[image:teachbuttoninvisible_option.jpg|400px]] | ||
</td> | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:teachbuttoninvisible_button.jpg]] | ||
+ | |||
+ | </td> | ||
+ | |||
+ | </tr> | ||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | |||
+ | |||
+ | ===[[image:Check.jpg|25px]] ENHANCED - AUTO MODE can now Always be STEP MODE === | ||
+ | |||
+ | <table cellpadding=10> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | For controlled benders that are hand-powered, it is always appropriate to run in STEP mode rather than AUTO mode. If this option is enabled, then AUTO mode always runs in STEP mode. | ||
+ | <br> | ||
+ | [[image:alwaysruninstepmode_option.jpg|400px]] | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | |||
+ | </td> | ||
+ | |||
+ | </tr> | ||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
+ | ===[[image:Check.jpg|25px]] ENHANCED - Output Diagnostic === | ||
+ | |||
+ | <table cellpadding=10> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | The Output Diagnostic was enhanced with 32 points visible on the screen, and larger controls. | ||
+ | <br> | ||
+ | [[image:cncbender_output_diagnostic.jpg|400px]] | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | |||
+ | </td> | ||
+ | |||
</tr> | </tr> | ||
</table> | </table> |
Latest revision as of 23:00, 28 January 2011
v12-20110128
|
NEW - Process List Commands Can Ignore STEP Mode
Some commands don't move the actuators on bender. They only setup the bender. Now these commands can be told to not PAUSE during STEP MODE. This will reduce the number of run-button or foot-pedal steps required to run through a part on the bender in STEP mode.
|
ENHANCED - Teach Mode Button Can Be Invisible
Some benders don't need TEACH Mode, so the Teach Mode button can be made invisible by enabling a switch in the low level options list.
|
ENHANCED - AUTO MODE can now Always be STEP MODE
For controlled benders that are hand-powered, it is always appropriate to run in STEP mode rather than AUTO mode. If this option is enabled, then AUTO mode always runs in STEP mode.
|
ENHANCED - Output Diagnostic
The Output Diagnostic was enhanced with 32 points visible on the screen, and larger controls.
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands