Difference between revisions of "Jog Motion"
From ATTWiki
(34 intermediate revisions by one user not shown) | |||
Line 1: | Line 1: | ||
+ | [[image:cncv12procontrol_withteachmode.jpg|300px]] | ||
+ | [[image:v12teachmode_buildcustomcommand.jpg|500px]] | ||
+ | |||
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
− | * A Jog Motion is a motion for a single axis or actuator that is stored in a [[Custom Command]] for use by [[Teach Mode]] if you choose to teach the bender.<br><br> | + | * A Jog Motion is a motion for a single axis or actuator that is stored in a [[Custom Command]] for use by [[Teach Mode]] if you choose to teach the bender. (See Screen 1)<br><br> |
− | * Jog Motions | + | * Custom Commands begin without any Jog Motions (See Screen 2) Add a Jog Motion using the Add a jog motion button<br><br> |
− | * | + | * Now the Jog Motion exists, but it is unassigned or empty. Click on the Jog Motion name cell to select a Jog Motion. (See Screen 3)<br><br> |
− | * | + | * Jog Motions are selected from the Jog Motion Selection menu by touching the Jog Motion name cell in a Custom Command menu (See Screen 4)<br><br> |
− | <br><br | + | |
− | + | ||
+ | * Jog Motion values can be entered using a keyboard, or entered using [[Teach Mode]]<br><br> | ||
− | + | * Multiple Jog Motions can be stored in a single Custom Command. When they are combined in a single Custom Command, then CNC Processor runs them all at the same time.<br><br> | |
− | + | ||
− | + | ||
− | + | ||
+ | [[image:cncv12_selectjogmotion.jpg|300px|thumb|Screen 4: Select a Jog Motion from the Selection menu]] | ||
+ | </td> | ||
+ | |||
+ | |||
+ | <td width=400> | ||
+ | [[image:cncv12_jogmotions.jpg|300px|thumb|Screen 1: Three Jog Motions in a Custom Command - All three run at the same time.]] | ||
+ | [[image:cncv12_customcommand_empty.jpg|300px|thumb|Screen 2: An empty Custom Command (no Jog Motions present)]] | ||
+ | [[image:cncv12_clickon_jogmotioncell.jpg|300px|thumb|Screen 3: Click on an unassigned (empty) Jog Motion cell to select a Jog Motion]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
Line 24: | Line 31: | ||
</table> | </table> | ||
+ | |||
+ | <br><br> | ||
+ | |||
+ | |||
+ | ==Jog Motion System Configuration== | ||
+ | |||
+ | <table> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | |||
+ | * The existence of a Jog Motion in the CNC Bender user interface is completely configurable.<br><br> | ||
+ | |||
+ | * You can add or edit your own Jog Motion or remove the existing Jog Motions from the user interface using a single configuration file.<br><br> | ||
+ | |||
+ | * You can even rename the Jog Motion name (or translate the motion to another language).<br><br> | ||
+ | |||
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | |||
<br><br> | <br><br> | ||
+ | |||
+ | =Other Pages= | ||
+ | *Back to [[CNC Bender]] | ||
+ | *Back to [[CNC Bender Software Updates]] | ||
+ | *See [[CNC Bender General Information]] | ||
+ | *See [[Teach Mode]] | ||
+ | *See [[Custom Command]]s | ||
+ | *See upgrade [[CNC Bender v12-20100105]] |
Latest revision as of 16:19, 21 January 2010
|
Jog Motion System Configuration
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
- See upgrade CNC Bender v12-20100105