Difference between revisions of "CNC Bender v12-20130724"
From ATTWiki
(Created page with "<table> <tr> <td width=200> ==v12-20130724== *Back to CNC Bender Software Updates </td> <td width=300> 300px<br> </td> <td> <...") |
(→25px Other Changes) |
||
| (2 intermediate revisions by one user not shown) | |||
| Line 22: | Line 22: | ||
<td width=300> | <td width=300> | ||
This new feature allows an operator to press AUTO mode or any manual mode button when in CYCLE HOLD, then pres CYCLE START and activate the command.<br><br> | This new feature allows an operator to press AUTO mode or any manual mode button when in CYCLE HOLD, then pres CYCLE START and activate the command.<br><br> | ||
| − | This feature is good for benders that use palm buttons to keep the bender in cycle hold (for example, the Allen Bradley 800Z Zero Force Touch Buttons | + | This feature is good for benders that use palm buttons to keep the bender in cycle hold (for example, the Allen Bradley 800Z Zero Force Touch Buttons shown here).<br><br> |
If AUTO mode is pressed while the bender is in CYCLE HOLD, then a large message will display for a few seconds asking for the operator to press CYCLE START.<br><br> | If AUTO mode is pressed while the bender is in CYCLE HOLD, then a large message will display for a few seconds asking for the operator to press CYCLE START.<br><br> | ||
</td> | </td> | ||
| Line 32: | Line 32: | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] NEW: PDA Stops During Cycle Hold Button Press=== | + | ===[[image:Check.jpg|25px]] NEW: PDA Forward Now Stops During Cycle Hold Button Press=== |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
| Line 42: | Line 42: | ||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
===[[image:Check.jpg|25px]] Other Changes=== | ===[[image:Check.jpg|25px]] Other Changes=== | ||
| Line 49: | Line 47: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | * | + | * Manual button presses when in CYCLE HOLD mode no longer clear the command with the "Use CYCLE START" message.<br><br> |
| − | * | + | * The AUTO button no longer disables when in CYCLE HOLD.<br><br> |
| − | * | + | * As with the previous version, COMDEFS can ignore CYCLE HOLD. For example, the Clamp and PD open commands can programmed to ignore the CYCLE HOLD state - and open even in CYCLE HOLD.<br><br> |
| − | + | ||
| − | + | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
Latest revision as of 21:03, 24 July 2013
v12-20130724
|
|
See CNC Bender Customer Service Page for an update.
NEW: Press Auto or Manual command then CYCLE START in CYCLE HOLD
|
This new feature allows an operator to press AUTO mode or any manual mode button when in CYCLE HOLD, then pres CYCLE START and activate the command. |
|
NEW: PDA Forward Now Stops During Cycle Hold Button Press
|
The PDA motion in a bend stops moving forward if the CYCLE HOLD button is pressed. (It would stop when the safety mat was stepped on - but not when the CYCLE HOLD button was pressed.) |
Other Changes
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender Customer Service Page for an update.
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
