Difference between revisions of "CNC Bender v12-20120622"
From ATTWiki
| (5 intermediate revisions by one user not shown) | |||
| Line 13: | Line 13: | ||
</table> | </table> | ||
__NOTOC__ | __NOTOC__ | ||
| − | ===[[image:Check.jpg|25px]] | + | |
| + | |||
| + | ===[[image:Check.jpg|25px]] New - Radius Level for LOAD Position in PREBEND=== | ||
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | The | + | The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part. These are the five options:<br> |
<br> | <br> | ||
| + | #Use the Radius from the first FRB Row | ||
| + | #Use Radius level 1 | ||
| + | #Use Radius level 2 | ||
| + | #Use Radius level 3 | ||
| + | #Use Radius level 4 | ||
| + | |||
</td> | </td> | ||
| Line 29: | Line 37: | ||
</table> | </table> | ||
| + | [[image:cncbender_radiuslevel_for_loading.jpg]] | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND=== |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | + | A new option allows the horizontal axis to move to a specific position for loading. This is a two-option feature:<br> | |
| + | </td> | ||
| + | |||
| + | <td width=300> | ||
| + | </td> | ||
| + | |||
| + | </tr> | ||
| + | </table> | ||
| + | [[image:cncbender_horizontalaxisloadposition.jpg]] | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180=== | ||
| + | |||
| + | <table cellpadding=10> | ||
| + | <tr valign=top> | ||
| + | <td width=400> | ||
| + | The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero. This has been fixed. | ||
<br> | <br> | ||
</td> | </td> | ||
| Line 47: | Line 71: | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] Repair - Robot Clear Bit Can Be High or Low=== |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | The | + | The Robot Clear bit always assumed that the TRUE signal was bit high. But some machines assume the opposite. This has been fixed. |
<br> | <br> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</td> | </td> | ||
| Line 69: | Line 87: | ||
</table> | </table> | ||
| − | + | ===[[image:Check.jpg|25px]] Enhancement - AutoSleep Removed=== | |
| − | ===[[image:Check.jpg|25px]] | + | |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=400> | <td width=400> | ||
| − | + | Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.<br> | |
<br> | <br> | ||
| − | + | Now the CNC Processor runs fast with our without AutoSleep enabled. | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
</td> | </td> | ||
Latest revision as of 01:31, 30 June 2012
v12-20120622
|
|
New - Radius Level for LOAD Position in PREBEND
|
The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part. These are the five options:
|
New - Horizontal Axis LOAD Position in PREBEND
|
A new option allows the horizontal axis to move to a specific position for loading. This is a two-option feature: |
Repair - Recovery Mode Rotate Spin 180
|
The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero. This has been fixed.
|
Repair - Robot Clear Bit Can Be High or Low
|
The Robot Clear bit always assumed that the TRUE signal was bit high. But some machines assume the opposite. This has been fixed.
|
Enhancement - AutoSleep Removed
|
Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed. |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
