Difference between revisions of "CNC Bender v12-20101021"
| (15 intermediate revisions by one user not shown) | |||
| Line 12: | Line 12: | ||
<br> | <br> | ||
| − | ===[[image:Check.jpg|25px]] NEW - Added Input Timer in PreEnable === | + | ===[[image:Check.jpg|25px]] NEW - Added Input Timer in PreEnable Processlist === |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=200> | <td width=200> | ||
| − | Schneider Lexium drives require a pulse to switch from READY to RUN mode. | + | Schneider Lexium drives require a pulse to switch from READY to RUN mode. <br><br> |
| + | |||
| + | Input TIMERS are now allowed in the PreEnable processlist to pulse the Lexium drives with an output point for a specific amount of time before the axes were enabled.<br><br> | ||
</td> | </td> | ||
<td> | <td> | ||
| Line 26: | Line 28: | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] FIXED - Early Mandrel | + | ===[[image:Check.jpg|25px]] FIXED - Early Mandrel Extract On Last Bend === |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=200> | <td width=200> | ||
| − | For benders with motion controlled PDA | + | For benders with motion-controlled [[PDA]] - the early mandrel extract now works.<br><br> |
| − | + | (Image courtesy of [http://www.toolsforbending.com/mandrels.asp Tools For Bending web site]) | |
</td> | </td> | ||
<td> | <td> | ||
[[image:ball_mandrel.jpg]]<br> | [[image:ball_mandrel.jpg]]<br> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
| Line 43: | Line 44: | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] CHANGED- KEYBOARD HANDLING === |
<table cellpadding=10> | <table cellpadding=10> | ||
<tr valign=top> | <tr valign=top> | ||
<td width=200> | <td width=200> | ||
| − | The | + | The keyboard features were completely locked out of previous main-window user interfaces to prevent a problem with accidental motion in the MANUAL page. This was too drastic and restrictive for operators that wanted to use the keyboard. |
| + | <br><br> | ||
| + | Now the keyboard works in every part of the user interface except with the manual buttons that can cause motion. Manual buttons will not receive any keyboard input. | ||
</td> | </td> | ||
<td> | <td> | ||
| − | + | [[image:keyboard.jpg|150px]] | |
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 21:05, 22 October 2010
|
|
Contents |
NEW - Added Input Timer in PreEnable Processlist
|
Schneider Lexium drives require a pulse to switch from READY to RUN mode. Input TIMERS are now allowed in the PreEnable processlist to pulse the Lexium drives with an output point for a specific amount of time before the axes were enabled. |
|
FIXED - Early Mandrel Extract On Last Bend
|
For benders with motion-controlled PDA - the early mandrel extract now works. |
|
CHANGED- KEYBOARD HANDLING
|
The keyboard features were completely locked out of previous main-window user interfaces to prevent a problem with accidental motion in the MANUAL page. This was too drastic and restrictive for operators that wanted to use the keyboard.
|
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands
