Difference between revisions of "Benderlink for FARO 1.5"
From ATTWiki
| (6 intermediate revisions by one user not shown) | |||
| Line 30: | Line 30: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:blinkfaro_autoreversefeature.jpg| | + | [[image:blinkfaro_autoreversefeature.jpg|350px]] |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 46: | Line 46: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | [[image:blinkfaro_reversefeature.jpg| | + | [[image:blinkfaro_reversefeature.jpg|350px]]<br><br> |
| − | [[image:blinkfaro_reverseflag.jpg| | + | [[image:blinkfaro_reverseflag.jpg|350px]] |
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
| + | <br><br> | ||
===[[image:Check.jpg|25px]] New - 64 Bit Compatibility === | ===[[image:Check.jpg|25px]] New - 64 Bit Compatibility === | ||
| Line 71: | Line 72: | ||
</table> | </table> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] Fix - User Interface Memory Leaks Repaired === |
<table> | <table> | ||
<tr> | <tr> | ||
| − | <td width= | + | <td width=550> |
| − | Benderlink now | + | Benderlink caused resource failures in previous versions. This has been resolved with this version of Benderlink for FARO.</td> |
| + | <td> | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | <br> | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] New - Screen Snap === | ||
| + | |||
| + | <table> | ||
| + | <tr> | ||
| + | <td width=550> | ||
| + | Benderlink now has screen snap capability. As you move Benderlink toward the screen edge, the window will snap to the edge of the screen.</td> | ||
<td> | <td> | ||
| − | |||
</td> | </td> | ||
</tr> | </tr> | ||
Latest revision as of 15:35, 23 July 2010
New - Reverse Bend Data Features
|
There are times when the nominal tube data may show the opposite point and bend order than used for bending. During communications, the bend order needs to be the same - so this allows operators to adjust the order of the bend data to fit both the CAM2 measure and the bend data setup in the bender control. |
New - Automatically Reverse Incoming Data Checkbox
|
Benderlink can now automatically reverse all incoming FARO CAM2 data if this new feature is enabled. |
|
New - Reverse Bender Data or Un-reverse Bender Data
|
Benderlink can now reverse the FARO CAM2 data after it is imported. The Reverse Bend Data button acts as a toggle for reversing and un-reversing the bend data.
|
|
New - 64 Bit Compatibility
This Benderlink is now compatible with 64 bit Windows
New - AddisonMckee Control Compatibility
| Benderlink for FARO now has extended Supravision network capabilities for AddisonMckee Mark IV and Mark V controls. |
|
Fix - User Interface Memory Leaks Repaired
| Benderlink caused resource failures in previous versions. This has been resolved with this version of Benderlink for FARO. |
New - Screen Snap
| Benderlink now has screen snap capability. As you move Benderlink toward the screen edge, the window will snap to the edge of the screen. |
Other Pages
- Back to the Benderlink for FARO page
