Difference between revisions of "CNC Bender v11-20091123"
From ATTWiki
| (9 intermediate revisions by one user not shown) | |||
| Line 11: | Line 11: | ||
</td> | </td> | ||
<td> | <td> | ||
| − | The changes in this version are | + | The changes in this version are changes to CNC Bender for better flexibility - including new operating systems. |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 25: | Line 25: | ||
__NOTOC__ | __NOTOC__ | ||
| + | |||
| + | ===[[image:Check.jpg|25px]] NEW- CNC Bender Can Now Run in 32 or 64 bit Windows Vista and Windows 7=== | ||
| + | <table> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | * CNC Bender previously only ran on Windows 2000 or Windows XP.<br><br> | ||
| + | * Now the licensing code is new and allows for operation in Windows Vista and Windows 7 either 32 or 64 bit versions. | ||
| + | <br><br> | ||
| + | </td> | ||
| + | |||
| + | <td> | ||
| + | |||
| + | [[image:Win_vista_logo.jpg|right|100px]] | ||
| + | [[image:win7logo.jpg|right|100px]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | |||
| + | </table> | ||
| + | |||
| + | <br><br> | ||
===[[image:Check.jpg|25px]] NEW- Editor for High Speed Constant Run Processlist=== | ===[[image:Check.jpg|25px]] NEW- Editor for High Speed Constant Run Processlist=== | ||
| Line 75: | Line 95: | ||
<br><br> | <br><br> | ||
| − | ===[[image:Check.jpg|25px]] | + | ===[[image:Check.jpg|25px]] REPAIR- Counter in RunPage is Updated to Zero When Run is Complete=== |
<table> | <table> | ||
| + | |||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | * | + | * The part count updated normally except when the Runlist Run is complete. This is corrected. |
| − | + | ||
</td> | </td> | ||
| − | |||
| − | |||
| − | |||
| − | + | <td width=450> | |
| − | + | [[image:runpage_counter.jpg|450px]] <br><br> | |
| − | <td width= | + | |
| − | + | ||
| − | + | ||
</td> | </td> | ||
| − | |||
| − | |||
| − | |||
</tr> | </tr> | ||
</table> | </table> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
<br><br> | <br><br> | ||
Latest revision as of 23:49, 23 November 2009
|
|
|
NEW- CNC Bender Can Now Run in 32 or 64 bit Windows Vista and Windows 7
|
  |
NEW- Editor for High Speed Constant Run Processlist
|
|
NEW- Better Warning for Missing Processlists
|
|
UPDATE- Improved Grids in Dynamic Option Lists
|
|
REPAIR- Counter in RunPage is Updated to Zero When Run is Complete
|
|
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender v11-20091104
- See CNC Bender General Information
- See Absolute Rotate
- See Absolute Rotate Offset Position
- See Final Feed Clearance
- See Mandrel Retract
- See Mandrel Retract Part Release
