Difference between revisions of "TubeCAD Pro v8-20071002"

From ATTWiki
Jump to: navigation, search
(25px New Prototype File Handling Abilities)
(25px User Selection of Prototype File Name for Either INCHES or MILLIMETERS)
Line 4: Line 4:
 
===[[image:Check.jpg|25px]] User Selection of Prototype File Name for Either INCHES or MILLIMETERS===
 
===[[image:Check.jpg|25px]] User Selection of Prototype File Name for Either INCHES or MILLIMETERS===
  
Prototype TubeCAD files are used to initialize the drawing setup to your preferences.  This new feature will allow a TubeCAD user to quickly switch from one prototype file to another to switch default blockup, color, linetype, and unit information - just by selecting a new prototype TubeCAD file.
+
Prototype TubeCAD files are used to initialize the drawing setup to your preferences like linear units, text size, blockup styles, etc..
  
Before this new feature, the prototype files loaded were fixed to a single file for either INCHES or MILLIMETERS.
+
Previously, the prototype filenames referred to by TubeCAD when it was clearing and preparing for a new part where fixed.  Now, the TubeCAD Pro OPTIONS FILE TAB menu now allows you to enter or select a unique prototype file for either millimeters or inches.  Simply right click on the drawing area and select Options to call up this menu.
  
The TubeCAD Pro OPTIONS menu FILE TAB now allows you to enter or select a unique prototype file for either millimeters or inches. 
+
Also, a new set of radio button controls allow you to choose which one of the two default prototype files is used to clear TubeCAD Pro whenever you start TubeCAD.
 
+
A new set of radio buttons allows you to choose which one of the two default prototype files is used to clear TubeCAD Pro when it is started.
+
  
 
[[image:tcadpro_options_menu_v8-20071002.jpg|450px]]
 
[[image:tcadpro_options_menu_v8-20071002.jpg|450px]]

Revision as of 20:14, 2 October 2007

Tcadpro logo.jpg


Check.jpg User Selection of Prototype File Name for Either INCHES or MILLIMETERS

Prototype TubeCAD files are used to initialize the drawing setup to your preferences like linear units, text size, blockup styles, etc..

Previously, the prototype filenames referred to by TubeCAD when it was clearing and preparing for a new part where fixed. Now, the TubeCAD Pro OPTIONS FILE TAB menu now allows you to enter or select a unique prototype file for either millimeters or inches. Simply right click on the drawing area and select Options to call up this menu.

Also, a new set of radio button controls allow you to choose which one of the two default prototype files is used to clear TubeCAD Pro whenever you start TubeCAD.

Tcadpro options menu v8-20071002.jpg




Check.jpg New Script Commands for the Command Engine

The NEW MILLIMETER or NEW INCH buttons in the TubeCAD toolbar (see below) now will use these internal filenames to call up the correct file. (The previous filenames were fixed.)

Tcadpro options newpart v8-20071002.jpg

For example, the the blue-ball button above calls out to a script named "presetin.scr". A script is a series of keystrokes that TubeCAD Pro will perform when the script is run. The script takes advantage of the new commands
[options_prototype_in]
and
[options_prototype_mm]
in the command engine. These two tokens lookup the current default prototype drawing names (either mm or inches), then reset TubeCAD with these prototype file settings.

Here is the script code for presetin.scr:

multicmdopen
_openprototype
|
"[options_prototype_in]"
multicmdclose



Here is the script code for presetmm.scr:

multicmdopen
_openprototype
|
"[options_prototype_mm]"
multicmdclose