VTube-LASER v2.9.3

Revision 2.9.3 Release Date: February 1, 2018 Back to VTube-LASER Back to VTube-LASER Updates See also VTube-STEP Updates Download in updates the VTube-LASER Support Page

NEW - MTA (MEASURED TUBE AVERAGING) - SUPER ACCURATE MEASURES MADE EASY

This feature was requested by MEC, Inc. after several weeks of tests. We designed the super-easy-to-use MTA feature. MEC Inc. (Mayville Engineering), one of our customer-reference companies, performed several tests on large-diameter tubes to confirm that measuring both sides of the tube has a positive impact on the measurement of tube shapes. They requested that we make creating averaged (hybrid) tubes easier for operators. The MTA feature that allows operators measure the tube, rotate it, measure it again, rotate it, etc. - as many times as they want to. And it's easy to do. Also, new buttons were added to the Tube Measure Control window to make using this feature very easy. See Video 76 in VTube-LASER Videos.

NEW - SEND ASSEMBLIES TO SOLIDWORKS

VTube-LASER can now send entire tube assemblies to SOLIDWORKS with one button press.

NEW - NUMALLIANCE CORRECTIONS ADDED

VTube-LASER now has an export option for NUMALLIANCE CSV files that is used to correct the NUMALLIANCE benders. Note: NUMALLIANCE benders only require the measured data for corrections. Measure the tube in VTube-LASER, then send the MEASURED tube data to the bender control, and it will then perform the correction.

NEW - REDESIGNED TUBE EXPORT MENU for QUICK EXPORT with NUMALLIANCE EXPORT ADDED

We redesigned the FILE menu for the MASTER, MEASURED, and MEASURED ALIGNED menus. Now it is referred to as EXPORT. The new menu has a drop-down box that allows for easier access to export choices.

NEW - Diameter Cut Plane - Maximum Cloud Radius ZERO Warning

VTube-LASER will take in only one point per laser stripe if the Maximum Cloud Radius value is accidentally zero to ZERO and the DCP is set to ACTIVE. Therefore, a new warning displays when you start a new measure and the value is set to ZERO with DCP active. VTube-LASER also opens the Cut Plane Setup Control window so that you can adjust the value. The only way to measure with the DCP Maximum Cloud Radius value set to zero is to set the DCP to INACTIVE.

NEW - DENGLER Bender Corrections Support ADDED

Dengler benders are known for bending long brake and fuel lines. This new communications protocol quickly adjusts the DENGLER MES bender files directly that can then be loaded into the DENGLER controls.

NEW - SUPPORT FOR MICROSCRIBE ARMS FROM REVWARE

VTube-LASER now supports the MicroScribe arms using ball probes. These arms are smaller and have fewer axes than regular laser scanning arms from HEXAGON or FARO, and are therefore less expensive. A VTube-LASER + MicroScribe Arm system costs only $21000 ($26000 with on-site training). The arm that we developed the link with is a MicroScribe i arm (shown on the right). You can view a PDF brochure here: MicroScribe i Brochure This arm has a two-foot reach (four-foot total volume) with an accuracy of +/- 0.005" (127 microns). Revware has arms that are accurate to +/-0.002" (51 microns). They also sell a slightly longer arm with higher accuracy than the "i" arm shown here.

NEW - GUIDE WINDOWS IN BENDER SETUP ADDED

We've put Guide Windows in the Bender Setup menu. They can stay open for as long you as you want - or close them anytime. They are less obtrusive than the dialogs that required the operator to press "OK" to continue.

Other

• Windows paint and stay-on-top issues were addressed for the VTube-LASER window. For example, it was not possible to bring other windows with focus on top of VTube-LASER. This has been resolved.

Other Pages

• See VTube-LASER Addata ZModem Communications Protocol for more information.
• Back to VTube-LASER
• Back to VTube Software Updates (for LASER Mode)
• See also VTube-STEP
• See also VTube-STEP Revisions
• See VTube-LASER Customer Support Page to download the latest version.
• See the tutorial on DCF - Dual Cylinder Fit
• See the tutorial on DCP - Diameter Cut Planes
• See VTube-LASER Cut Planes
• See How to Measure Tubes Attached to an Evaporator with the DCP Feature