Difference between revisions of "VTube-LASER Videos for HEXAGON ROMER"
(→Version 2.9.18) |
(→Version 2.9.19) |
||
Line 16: | Line 16: | ||
+ | |||
+ | ===Version 2.9.21=== | ||
+ | |||
+ | ====Video 107: Corrections Loop with SOCO Beckhoff Controls==== | ||
+ | |||
+ | |||
+ | <table width=700> | ||
+ | <tr> | ||
+ | <td width=300> | ||
+ | This demo video shows how VTube-LASER performs corrections loop communications with SOCO Beckhoff controls. | ||
+ | </td> | ||
+ | <td width=200> | ||
+ | [[image:vtubelaser_v2.9.21.video_soco_beckhoff_communications.png|300px]]<br> | ||
+ | </td> | ||
+ | <td width=300> | ||
+ | * View [https://vimeo.com/356003359 Vimeo] | ||
+ | * View [https://www.advancedtubular.com/vtube-laser/vtl_v2.9.21_SOCO_SV-M_Protocol.mp4 MP4] | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | </table> | ||
+ | <br><br> | ||
===Version 2.9.19=== | ===Version 2.9.19=== | ||
Line 58: | Line 80: | ||
</table> | </table> | ||
<br><br> | <br><br> | ||
− | |||
===Version 2.9.18=== | ===Version 2.9.18=== |
Revision as of 16:30, 26 August 2019
See a list of VTube-LASER videos for ROMER Absolute Arms from HEXAGON on this page.
|
Version 2.9.21
Video 107: Corrections Loop with SOCO Beckhoff Controls
This demo video shows how VTube-LASER performs corrections loop communications with SOCO Beckhoff controls. |
Version 2.9.19
Video 104: Demo of VTube-LASER Measuring from 2mm to 450mm Tube and Pipe + Square
This demo video shows the wide range of tube, pipe, wire, string types that VTube-LASER can scan with a laser scanner arm. |
Video 103: VTube-LASER "Timer Accept" Feature Cuts Button Press Counts in Half
This video shows how the TIMER ACCEPT button can decrease your button presses during UniScan tube measuring by half. |
Version 2.9.18
Video 100: How To Calculate the Centerline Radius in a Measured 180-degree Bend
This video shows how to use the Dimension Control window to calculate the true radius of a 180-degree bend. |
|
Video 99: See VTube-LASER Reverse Engineer a RZR Side by Side Custom Tube Assembly using a HEXAGON RA8 Arm
This video shows Michael Cone using VTube-LASER to reverse engineer a custom 8 tube assembly for a RZR Side by Side in 8 minutes - including sending the part to SOLIDWORKS. |
Video 98: About the Small Diameter Warning
This video shows how Small Diameter Warning works along with its setup. |
Video 96: VTube-STEP and VTube-LASER New Radius Features
See the new radius features in this video. In Part Setup:
|
Video 95: VTube-LASER Communicating with BendPro G2 on an RbSA Industrial BOOST Trainer
Michael Cone simulates a corrections loop between VTube-LASER v2.9.18 and BendPro G2 on an RbSA Industrial BOOST trainer.
Version 2.9.17
Video 94: Five Major Enhancements to VTube-LASER Version 2.9.17 - FEATURING the HEXAGON ABSOLUTE ARM
Michael Cone shows 5 major new features in VTube-LASER v2.9.17. (Released on December 30, 2018).
Version 2.9.16
Video 90: How to Attach and Use the ROMER Absolute 8-series Scanner in VTube-LASER
This is a video where Michael Cone shows how to attach and use the 8-series style arm scanner with VTube-LASER.
Version 2.9.10
Video 86: VTube-LASER's LASER SCAN FILTER SOUND
This is a short video that shows how the Laser Scan Filter sound helps you know when all laser scan data is removed by the scan filters.
Video 84: Measuring Convoluted Tube and Wire with VTube-LASER
This video shows VTube-LASER's ability to measure extremely convoluted parts with a ROMER Absolute Arm with Integrated Scanner. This wire part wraps back on itself in several places, making it very challenging. Because VTube-LASER has scanning filters, it can measure this part with a wider laser stripe.
Version 2.9.4
Video 78: VTube-LASER Corrects an SMT Bender Using a ROMER Absolute Arm
This video demonstrates the correction process between VTube-LASER and an SMT remanufactured VB300 bender. We use a ROMER Absolute Arm with integrated scanner in this video.
Version 2
Video 2: SCANNING SPEED TEST ON TWO TYPES OF TUBES
This video shows speed tests on two very different kinds of tube shapes:
|
Video 1: INTRODUCING VTUBE-LASER MEASURING WITH A ROMER ABSOLUTE ARM
As of November 1, 2017, VTube-LASER can measure tubes with ROMER Absolute Arms from HEXAGON. This video shows a measurement of a tube using a 3.5 meter ROMER arm. |
Other Pages
- Back to VTube-LASER