Difference between revisions of "VTube-LASER UniScan Automatic Laser Separation"
From ATTWiki
(18 intermediate revisions by one user not shown) | |||
Line 6: | Line 6: | ||
==UniScan Automatic Separation Tutorial== | ==UniScan Automatic Separation Tutorial== | ||
− | |||
− | |||
* Back to [[VTube-LASER]] | * Back to [[VTube-LASER]] | ||
Line 23: | Line 21: | ||
__TOC__ | __TOC__ | ||
+ | |||
+ | |||
+ | [[image:ra8_stripes_auto_laser_separation.png|500px]]<br><br> | ||
Line 37: | Line 38: | ||
<td> | <td> | ||
− | [[image:vtl_v2.9. | + | [[image:vtl_v2.9.18_AutomaticLaserSeparation_Graphic.png|800px]] |
</td> | </td> | ||
Line 45: | Line 46: | ||
<br><br> | <br><br> | ||
− | ==How AUTOMATIC LASER SEPARATION Method | + | |
+ | ==How AUTOMATIC LASER SEPARATION Method Works == | ||
<table cellpadding=10 width=1200> | <table cellpadding=10 width=1200> | ||
Line 52: | Line 54: | ||
<td width=300> | <td width=300> | ||
*This mode only works with parts that have MASTER data.<br><br> | *This mode only works with parts that have MASTER data.<br><br> | ||
− | *If a part does not have MASTER data (like | + | *The FACTOR value is multiplied against the current MASTER length to get a new separation distance. The valid ranges are 0 to 0.5. If you use 0.5, then VTube-LASER will attempt to lay two stripes per straight. A recommended starting value is 0.025 (40 stripes per straight).<br><br> |
+ | *If a part does not have MASTER data (like for Reverse Engineering), then the regular UniScan Cylinder Separation Distance value is used.<br><br> | ||
*If the separation distance is ever less than 0.004" (100 microns), then the value reverts to 100 microns.<br><br> | *If the separation distance is ever less than 0.004" (100 microns), then the value reverts to 100 microns.<br><br> | ||
*If the MASTER length is less than or equal to ZERO, then the separation value reverts to the regular UniScan Cylinder Separation Distance value.<br><br> | *If the MASTER length is less than or equal to ZERO, then the separation value reverts to the regular UniScan Cylinder Separation Distance value.<br><br> | ||
− | |||
</td> | </td> | ||
<td> | <td> | ||
− | [[image:vtl_v2.9. | + | [[image:vtl_v2.9.18_AutomaticLaserSeparation_LargeBanner.png|700px]]<br><br> |
</td> | </td> | ||
Line 66: | Line 68: | ||
</table> | </table> | ||
− | |||
<br><br> | <br><br> | ||
+ | |||
+ | |||
+ | ==Real-time Separation Distance Reported== | ||
+ | |||
+ | <table cellpadding=10 width=1200> | ||
+ | <tr valign=top> | ||
+ | |||
+ | <td width=300> | ||
+ | The measure guide window indicates the current real-time separation distance. | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | [[image:vtl_v2.9.18_AutomaticLaserSeparation_tubemeasureguide.png|700px]]<br><br> | ||
+ | </td> | ||
+ | |||
+ | </tr> | ||
+ | |||
+ | </table> | ||
=Other Pages= | =Other Pages= |
Latest revision as of 01:34, 9 March 2019
UniScan Automatic Separation Tutorial
|
Contents |
About the AUTOMATIC LASER SEPARATION Method for UniScan Mode
The AUTOMATIC LASER SEPARATION method allows VTube-LASER to automatically control the separation distance between laser stripes based on the known MASTER tube length. |
How AUTOMATIC LASER SEPARATION Method Works
|
Real-time Separation Distance Reported
The measure guide window indicates the current real-time separation distance. |
Other Pages
- See VTube-LASER Addata ZModem Communications Protocol for more information.
- Back to VTube-LASER
- Back to VTube Software Updates (for LASER Mode)
- See also VTube-STEP
- See also VTube-STEP Revisions
- See VTube-LASER Customer Support Page to download the latest version.
- See the tutorial on DCF - Dual Cylinder Fit
- See the tutorial on DCP - Diameter Cut Planes
- See VTube-LASER Cut Planes
- See How to Measure Tubes Attached to an Evaporator with the DCP Feature