Difference between revisions of "CNC Bender v15.9.5"
(→25px FIXED: Window Border Feature) |
|||
(39 intermediate revisions by one user not shown) | |||
Line 2: | Line 2: | ||
<tr> | <tr> | ||
<td width=400> | <td width=400> | ||
− | ===v15.9.5 - September | + | ===v15.9.5 - September 16, 2017=== |
*Back to [[CNC Bender Software Updates]] | *Back to [[CNC Bender Software Updates]] | ||
</td> | </td> | ||
Line 15: | Line 15: | ||
__NOTOC__ | __NOTOC__ | ||
− | ==[[image:Check.jpg|25px]] | + | ==[[image:Check.jpg|25px]] BIG CHANGE: CYCLE TIME REDUCTION with "END CUSTOM COMMANDS" Feature== |
+ | <table width=1000> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | '''If you use CUSTOM COMMANDS for avoidance moves in any of your bend programs, then we strongly recommend that you upgrade to version 15.9.5 for this feature alone.''' <h2>This new feature can shave seconds off of bend cycle times.</h2><br><br> | ||
+ | The big change in this version is that CNC Bender allows the operator to skip unused CUSTOM COMMANDS in the process list. The end effective can be shaving several seconds off of cycle times for parts that use CUSTOM COMMANDS for avoidance moves during bending.<br><br> | ||
+ | </td> | ||
+ | <td width=600> | ||
+ | [[image:Cnc_v15.9.5_endcustomcommands_tutorial.png|500px]] | ||
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | |||
+ | ==[[image:Check.jpg|25px]] FIXED: Call to Windows Onscreen Keyboard Working Again in Win7 and Win10== | ||
<table width=1000> | <table width=1000> | ||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
− | + | CNC Bender could not load the Windows onscreen keyboard in Windows 7 and Windows 10 in 64 bit mode.<br><br> | |
− | + | This has been resolved. | |
</td> | </td> | ||
<td width=600> | <td width=600> | ||
− | [[image:cnc_v15.9.5 | + | [[image:cnc_v15.9.5 osk.png|400px]] |
− | + | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
+ | <br><br> | ||
==[[image:Check.jpg|25px]] FIXED: Window Border Feature== | ==[[image:Check.jpg|25px]] FIXED: Window Border Feature== | ||
Line 34: | Line 47: | ||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
− | The Window border feature now correctly maximizes the CNC Bender window when the window border is toggled OFF. | + | The Window border feature now correctly maximizes the CNC Bender window when the window border is toggled OFF.<br><br> |
+ | This feature allows users to gain access to Windows while CNC Bender is still running. | ||
</td> | </td> | ||
<td width=600> | <td width=600> | ||
Line 43: | Line 57: | ||
<br><br> | <br><br> | ||
− | ==[[image:Check.jpg|25px]] FIXED: Motion PDA | + | ==[[image:Check.jpg|25px]] FIXED: Motion PDA Collision Protection in Manual Absolute== |
<table width=1000> | <table width=1000> | ||
<tr> | <tr> | ||
<td width=300> | <td width=300> | ||
+ | This change is for motion-controlled PDAs.<br><br> | ||
CNC Bender no longer allows the PDA to move forward to an ABSOLUTE position when the bend arm is positioned less than 90 degrees. | CNC Bender no longer allows the PDA to move forward to an ABSOLUTE position when the bend arm is positioned less than 90 degrees. | ||
</td> | </td> | ||
Line 55: | Line 70: | ||
</table> | </table> | ||
<br><br> | <br><br> | ||
+ | |||
+ | ==[[image:Check.jpg|25px]] FIXED: Galil Communications Reset Issue== | ||
+ | <table width=1000> | ||
+ | <tr> | ||
+ | <td width=300> | ||
+ | CNC Bender can sometimes request a Galil motion controller communications reset on slower computers.<br><br> | ||
+ | This has been resolved. | ||
+ | </td> | ||
+ | <td width=600> | ||
+ | [[image:galil_dmc_module.png|400px]] | ||
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | <br><br> | ||
+ | |||
==Other Pages== | ==Other Pages== |
Latest revision as of 20:22, 16 September 2017
v15.9.5 - September 16, 2017
|
BIG CHANGE: CYCLE TIME REDUCTION with "END CUSTOM COMMANDS" Feature
If you use CUSTOM COMMANDS for avoidance moves in any of your bend programs, then we strongly recommend that you upgrade to version 15.9.5 for this feature alone. This new feature can shave seconds off of bend cycle times.The big change in this version is that CNC Bender allows the operator to skip unused CUSTOM COMMANDS in the process list. The end effective can be shaving several seconds off of cycle times for parts that use CUSTOM COMMANDS for avoidance moves during bending. |
FIXED: Call to Windows Onscreen Keyboard Working Again in Win7 and Win10
CNC Bender could not load the Windows onscreen keyboard in Windows 7 and Windows 10 in 64 bit mode. |
FIXED: Window Border Feature
The Window border feature now correctly maximizes the CNC Bender window when the window border is toggled OFF. |
FIXED: Motion PDA Collision Protection in Manual Absolute
This change is for motion-controlled PDAs. |
FIXED: Galil Communications Reset Issue
CNC Bender can sometimes request a Galil motion controller communications reset on slower computers. |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands