Difference between revisions of "CNC Bender v15.9.5"

From ATTWiki
Jump to: navigation, search
(25px BIG CHANGE: CYCLE TIME REDUCTION for CUSTOM COMMAND USERS)
(25px BIG CHANGE: CYCLE TIME REDUCTION for CUSTOM COMMAND USERS)
Line 20: Line 20:
 
<tr>
 
<tr>
 
<td width=300>
 
<td width=300>
 +
<H3>If you use CUSTOM COMMANDS in any of your bend programs in CNC Bender ProControl, then we strongly recommend that you upgrade your CNC Bender for this feature alone.</h3><br><br>
 
The big change in this version is that CNC Bender allows the operator to skip unused CUSTOM COMMANDS in the process list. The end effective can be shaving several seconds off of cycle times for parts that use CUSTOM COMMANDS for avoidance moves during bending.<br><br>
 
The big change in this version is that CNC Bender allows the operator to skip unused CUSTOM COMMANDS in the process list. The end effective can be shaving several seconds off of cycle times for parts that use CUSTOM COMMANDS for avoidance moves during bending.<br><br>
<H3>If you use CUSTOM COMMANDS in any of your bend programs in CNC Bender ProControl, then we strongly recommend that you upgrade your CNC Bender for this feature alone.</h3></td>
+
</td>
 
<td width=600>
 
<td width=600>
[[image:cnc_v15.9.5 End Custom Commands In Editor.png|400px]]<br><br>
 
 
[[image:cnc_v15.9.5 End Custom Commands Skip All Below.png|400px]]
 
[[image:cnc_v15.9.5 End Custom Commands Skip All Below.png|400px]]
 
</td>
 
</td>

Revision as of 19:16, 16 September 2017

v15.9.5 - September 14, 2017

Cncbender v15 logo.png


Check.jpg BIG CHANGE: CYCLE TIME REDUCTION for CUSTOM COMMAND USERS

If you use CUSTOM COMMANDS in any of your bend programs in CNC Bender ProControl, then we strongly recommend that you upgrade your CNC Bender for this feature alone.



The big change in this version is that CNC Bender allows the operator to skip unused CUSTOM COMMANDS in the process list. The end effective can be shaving several seconds off of cycle times for parts that use CUSTOM COMMANDS for avoidance moves during bending.

Cnc v15.9.5 End Custom Commands Skip All Below.png

Check.jpg NEW: Added Jog Motion "End Custom Commands"

When building Custom Commands, it is helpful to be able to indicate when a Custom Command is the last one in order to save time in the run cycle.

When CNC Bender Processor encounters this command, it skips to the end of that custom command section in the process list.

Cnc v15.9.5 End Custom Commands In Editor.png

Cnc v15.9.5 End Custom Commands Skip All Below.png

Check.jpg FIXED: Window Border Feature

The Window border feature now correctly maximizes the CNC Bender window when the window border is toggled OFF.

Cnc v15.9.5 Toggle Border.png



Check.jpg FIXED: Motion PDA Crash Protection in Manual Absolute

This change is for motion-controlled PDAs.

CNC Bender no longer allows the PDA to move forward to an ABSOLUTE position when the bend arm is positioned less than 90 degrees.

Cnc v15.9.5 PDA Absolute Protect.png




Check.jpg FIXED: Galil Communications Reset Issue

CNC Bender can sometimes request a Galil motion controller communications reset on slower computers.

This has been resolved.

Galil dmc module.png




Check.jpg FIXED: Call to Windows Onscreen Keyboard Working Again

CNC Bender could not load the Windows onscreen keyboard in Windows 7 and Windows 10 in 64 bit mode.

This has been resolved.

Cnc v15.9.5 osk.png



Other Pages