Difference between revisions of "End-Scan Using the End Wall"
(→About the End Wall Orientation) |
(→How To Use This End-Scan Technique) |
||
(20 intermediate revisions by one user not shown) | |||
Line 12: | Line 12: | ||
</tr> | </tr> | ||
</table> | </table> | ||
− | + | __TOC__ | |
Line 20: | Line 20: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=500> | <td width=500> | ||
− | We recommend this for increased precision where it is possible to strike the end wall. | + | We recommend this for increased precision where it is possible to strike the end wall. The End Wall method is also very useful for thicker wall tubes. |
<br><br> | <br><br> | ||
+ | The advantage of this method is that it is less prone to outlier points. The disadvantage is that it is hard to aim at thinner walls.<br><br> | ||
For tube walls with high-reflectivity with burrs or saw marks, we recommend either a coating (see below) or the most precise [[End-Scan Using End Targets]]. | For tube walls with high-reflectivity with burrs or saw marks, we recommend either a coating (see below) or the most precise [[End-Scan Using End Targets]]. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
Line 51: | Line 35: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
− | * Align the scanner | + | * Align the scanner so that it touches one end wall of the tube.<br><br> |
− | + | * Attempt to hold the laser motionless when collecting the stripes to increase repeatability.<br><br> | |
− | * Attempt to hold the laser motionless when collecting the stripes | + | |
* Consistently place the line across the same area of the tube end from measure to measure.<br><br> | * Consistently place the line across the same area of the tube end from measure to measure.<br><br> | ||
− | *Press the green button until VTube-LASER is finished scanning all the end stripes.<br><br> | + | * Press the green button until VTube-LASER is finished scanning all the end stripes.<br><br> |
− | + | * If you are scanning an end that is highly reflective, then coat the end with powder or white paint marker (See Avoiding Outliers below).<br><br> | |
− | + | * After you perform this scan, you should be able to observe a straight line of points on the screen that represent the end wall. If you don't see this line, then repeat the end scan measurement by using the "Previous" button in the measurement control window. | |
</td> | </td> | ||
<td width=300> | <td width=300> | ||
− | [[image: | + | [[image:endwall_whitepaint_scan_llp.jpg|300px]]<br><br> |
+ | [[image:endwall_whitepaint_scan.jpg|300px]] | ||
</td> | </td> | ||
</tr> | </tr> | ||
</table> | </table> | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
===Avoiding Outliers=== | ===Avoiding Outliers=== | ||
Line 89: | Line 55: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
− | When scanning the end walls of highly reflective tubing with striations like shown in the image on the right, it is better to either cover the end with a coat of Maganaflux, Dynaflux, foot powder spray, or cover it with an end target to avoid outlier points.<br><br> | + | When scanning the end walls of highly reflective tubing with striations like shown in the image on the right, it is better to either cover the end with a coat of Maganaflux, Dynaflux, foot powder spray, white marking paint pen, or cover it with an end target to avoid outlier points.<br><br> |
− | The image below an end target plastic label attached to the end of the same tube. In this case, there are no striations visible.<br><br> | + | The image below shows an end target plastic label attached to the end of the same tube. In this case, there are no striations visible.<br><br> |
[[image:EndWithEndWall_HighReflective_Striation_EndTarget.jpg|200px]] | [[image:EndWithEndWall_HighReflective_Striation_EndTarget.jpg|200px]] | ||
+ | <br><br> | ||
+ | See also [[Surface Paint]] for using a white paint marker for the prep of the end scan. | ||
</td> | </td> | ||
<td width=300> | <td width=300> | ||
Line 104: | Line 72: | ||
* See also [[End-Scan Using End Targets]] | * See also [[End-Scan Using End Targets]] | ||
* Back to [[VTube-LASER]] | * Back to [[VTube-LASER]] | ||
+ | * See also [[Surface Paint]] |
Latest revision as of 05:43, 31 January 2017
How to perform the end-wall end scan.
|
Contents |
About the End Wall Technique
We recommend this for increased precision where it is possible to strike the end wall. The End Wall method is also very useful for thicker wall tubes.
|
How To Use This End-Scan Technique
|
Avoiding Outliers
When scanning the end walls of highly reflective tubing with striations like shown in the image on the right, it is better to either cover the end with a coat of Maganaflux, Dynaflux, foot powder spray, white marking paint pen, or cover it with an end target to avoid outlier points. |
Other Pages
- See also End-Scan Using the Scissor Motion
- See also End-Scan Using End Targets
- Back to VTube-LASER
- See also Surface Paint