Difference between revisions of "Eaton Leonard Lightspeed Communications Setup"

From ATTWiki
Jump to: navigation, search
(Setup VTube for Communications with Supravision Network)
(STEP 5: SEND a Part from the VTube-LASER)
Line 158: Line 158:
  
 
===STEP 5: SEND a Part from the VTube-LASER===
 
===STEP 5: SEND a Part from the VTube-LASER===
<table>
+
<table width=800>
 +
<tr valign=top>
 +
<td width=300>
 +
Use the [[VTube-STEP]] Bender Output menu to send new part data to a bender using Supravision Network protocol.
 +
<br><br>
 +
Go to the SV Network tab and choose the bender number.  This will use the Benderlink setup in System Options to control the SVNET path.<br><br>
  
<tr>
+
* The Supravision Network protocol uses a bender number (from 1 to 99) to indicate which bender should pickup and use the Supravision file that is being saved by VTube-STEP to the file path in the network box.  Use whatever you have programmed into the EL LightSpeed setup for bender number.<br><br>
<td width="300" valign=top>
+
* The LightSpeed uses the Part Number value from the VTube PART SETUP menu to create a part file if it does not exist on the LightSpeed hard driveIf it does exist, then the data can be merged into the existing file with the same part number.
From the measuring center, send a part to the LightSpeed.  (This assumes that the connection has been made and that the SVNET protcol is being used, and that the appropriate bender number is used at the measuring center.<br><br>
+
  
The screen on the right shows an example Bender Setup screen in [[VTube-LASER]] for communication.<br><br>
 
To send new data, choose the bender number, set the Part Number (if it is not, enter the "Bender Setup" menu, and press the AUTO SEND button.<br><br>
 
'''Keep in mind that the PART NUMBER value in VTube is the name that will be used by the LightSpeed to save the part data that it received.'''
 
 
</td>
 
</td>
<td valign=top>
+
<td>
[[image:vtube-laser_v2.2_bendersetup_sendbluecolumns.png|400px]]<br><br>
+
[[image:vtube-step_v2.2_svnet.png|400px]]<br><br>
 
</td>
 
</td>
</tr>
 
  
 +
</tr>
 
</table>
 
</table>
 
<br><br>
 
<br><br>

Revision as of 22:40, 18 December 2015

This document outlines the basic communications setup for a Lightspeed control.

EL Lightspeed.jpg




Setup VTube for Communications with Supravision Network

The VTube Benderlink setup grid needs to be properly configured to for Supravision Network communications before it will work with the LightSpeed.

The instructions that follow assume that VTube has been setup using the instructions.

See Setup VTube for Supravision Network Communication for detailed instructions on how configure VTube for communications.

Vtube benderlinkgrid.png

Setup Eaton Leonard LIGHTSPEED for Communications with Supravision Network

This is good for use in connecting with our VTube-LASER, VTube-STEP, and Benderlink software packages. All of them are equipped with the Supravision Network protocol - which is a protocol LightSpeed understands.

STEP 1: System Menu and Administrative Control

Change to the Systems menu. If you are not running the operator station as an administrator, then press SECURITY and enter the administrator code. (The default code is "123".)

Press the DEVICE CONFIG button.

EL Lightspeed SystemMode.png

STEP 2: Device Config / Machine Menu

In DEVICE CONFIG, enter the MACHINE menu.

Select a Measure Machine tab. LightSpeed can store four simultaneous measuring center setups for connection to multiple measuring centers.

  • NAME: The name value has no effect on the protocol. However, you can give the setup a name here.

  • PROTOCOL: For communications with our software, select the SupraGauge protocol.

  • BENDER NUMBER: Set the bender to a unique integer number. This is very important if you have multiple benders that share the same network location for transfer of data files.

    The bender number allows each bender to understand if the data files dropped in the shared path are its responsibility or another bender's.

    The original SV protocol can handle bender numbers from 1 to 99. VTube can go higher if necessary.

  • CHECKBOX OPTIONS: Select any of the checkbox options that you want to enable.

    • LOG: To log activity as it occurs

    • METRIC: To make all linear data communicate in Millimeters rather than the default Inches

    • PRESET CLR: To ignore any incoming Centerline Radius data. If you leave this disabled, then you will probably need to setup the CLR after LightSpeed receives a new part file from the measuring center.

  • NETWORK PATH: Set the Network Path to a location on the network that allows read/write access. This is the path where all machines and measuring centers will drop and pickup command files using the Supravision Network protocol.

EL Lightspeed DeviceConfig Machine.png

EL Lightspeed DeviceConfig Machine MeasuringCenterSetup.png



VTube-STEP Communications Test With LightSpeed

VTube-STEP is the version of VTube that allows you to send data from a model to a bender. (VTube-LASER can SEND and RECALL. See the VTube-LASER section below.) This section is for testing the LightSpeed control with with VTube-STEP.

In order to communicate with the LightSpeed control, it's necessary to switch on remote communications in the control in the user interface.

STEP 1: Exit AUTO Mode

Be sure to exit AUTO mode if that is the mode it is currently in. LightSpeed does not communicate if it is in AUTO mode.

STEP 2: Enter the Vector Menu

Click on the "Vector" button on the right side of the screen.

LightSpeed ProgramScreen VectorButton.png


STEP 3: Choose the VMM for VTube

Newer versions of LightSpeed let you choose which measuring center to communicate with.

Choose the VTube option.

LightSpeed VMM Choice.png

STEP 4: Allow Network Control

In the VECTOR menu, press the "Allow Network Control" button until it turns orange. (Orange indicates that it is toggled on.)

LightSpeed ProgramScreen AllowNetworkControl.png



STEP 5: SEND a Part from the VTube-LASER

Use the VTube-STEP Bender Output menu to send new part data to a bender using Supravision Network protocol.

Go to the SV Network tab and choose the bender number. This will use the Benderlink setup in System Options to control the SVNET path.

  • The Supravision Network protocol uses a bender number (from 1 to 99) to indicate which bender should pickup and use the Supravision file that is being saved by VTube-STEP to the file path in the network box. Use whatever you have programmed into the EL LightSpeed setup for bender number.

  • The LightSpeed uses the Part Number value from the VTube PART SETUP menu to create a part file if it does not exist on the LightSpeed hard drive. If it does exist, then the data can be merged into the existing file with the same part number.

Vtube-step v2.2 svnet.png



STEP 6: Observe the LightSpeed Communications Status Box

The Communications Status box in the LightSpeed Vector menu should show activity - like that the incoming file was saved.

You will also see the options of Overwriting the part data, or Importing the YBC data only. Overwriting the part data will allow the new data to completely overwrite the part in memory. Pressing the YBC data only will change only the YBC data in memory with the incoming data.

For setting up a new part, you can press overwrite. For corrections you can press YBC data only.

In this test, press Overwrite Part Data.

If you press Overwrite the Part Data, then LightSpeed will clear the current setup and clear the Tools. A tool set will need to be recalled to clear the red cells in the ALL page Bend Die column.

LightSpeed ProgramScreen ReceivedData2.png



STEP 7: Perform a RECALL at VTube-LASER

Change any value in the YBC data. Make the value change easily recognizable for when we recall the data in VTube-LASER.

Now, at VTube-LASER press RECALL. LightSpeed should answer VTube-LASER with the new data in the blue columns.

If the new values are displayed in the blue LRA columns, then the communication was successful.

Vtube-laser v2.2 bendersetup recall lra from bender.png





VTube-LASER Communications Test With LightSpeed

VTube-LASER is the version of VTube that communicates with a FARO arm in order to measure tubes and correct benders. It's communications capabilities are more sophisticated than VTube-STEP. VTube-STEP can send data to the bender. VTube-LASER can SEND and RECALL. This section is for testingthe LightSpeed control with with VTube-LASER.

In order to communicate with the LightSpeed control, it's necessary to switch on remote communications in the control in the user interface.

STEP 1: Exit AUTO Mode

Be sure to exit AUTO mode if that is the mode it is currently in. LightSpeed does not communicate if it is in AUTO mode.

STEP 2: Enter the Vector Menu

Click on the "Vector" button on the right side of the screen.

LightSpeed ProgramScreen VectorButton.png


STEP 3: Choose the VMM for VTube

Newer versions of LightSpeed let you choose which measuring center to communicate with.

Choose the VTube option.

LightSpeed VMM Choice.png

STEP 4: Allow Network Control

In the VECTOR menu, press the "Allow Network Control" button until it turns orange. (Orange indicates that it is toggled on.)

LightSpeed ProgramScreen AllowNetworkControl.png



STEP 5: SEND a Part from the VTube-LASER

From the measuring center, send a part to the LightSpeed. (This assumes that the connection has been made and that the SVNET protcol is being used, and that the appropriate bender number is used at the measuring center.

The screen on the right shows an example Bender Setup screen in VTube-LASER for communication.

To send new data, choose the bender number, set the Part Number (if it is not, enter the "Bender Setup" menu, and press the AUTO SEND button.

Keep in mind that the PART NUMBER value in VTube is the name that will be used by the LightSpeed to save the part data that it received.

Vtube-laser v2.2 bendersetup sendbluecolumns.png



STEP 6: Observe the LightSpeed Communications Status Box

The Communications Status box in the LightSpeed Vector menu should show activity - like that the incoming file was saved.

You will also see the options of Overwriting the part data, or Importing the YBC data only. Overwriting the part data will allow the new data to completely overwrite the part in memory. Pressing the YBC data only will change only the YBC data in memory with the incoming data.

For setting up a new part, you can press overwrite. For corrections you can press YBC data only.

In this test, press Overwrite Part Data.

If you press Overwrite the Part Data, then LightSpeed will clear the current setup and clear the Tools. A tool set will need to be recalled to clear the red cells in the ALL page Bend Die column.

LightSpeed ProgramScreen ReceivedData2.png



STEP 7: Perform a RECALL at VTube-LASER

Change any value in the YBC data. Make the value change easily recognizable for when we recall the data in VTube-LASER.

Now, at VTube-LASER press RECALL. LightSpeed should answer VTube-LASER with the new data in the blue columns.

If the new values are displayed in the blue LRA columns, then the communication was successful.

Vtube-laser v2.2 bendersetup recall lra from bender.png



Solving LightSpeed Bend Die / Incoming RADIUS Mismatch Issue

If you send a part to the LightSpeed that has dies that do not match the current die setup, then the Bend Die columns in the VIEW page will turn red - indicating a problem.

The key to fixing the problem is to be sure the incoming radius eventually matches the TOOL page die radius value.

Lightspeed red benddie cells.png

SOLUTION 1: Change the Radius Values in VTube before Sending Data

It's easy to change the radius values for a tube model before sending the data to the bender. In the video example, you will see a radius value of 1". However, in the Eaton Leonard LightSpeed, the die centerline radius is 1.125". So, just before sending data to the bender, we change the radius to match the bend die on the bender. This does not change the shape of the tube in space. It only changes the lengths between bends.

Click on the image to view the video.

Vtube-step v2 2 change radii then transfer to bender video.png

SOLUTION 2: Be sure the TOOLS Page Is Setup With Non Zero Values

When you clear a part, the process also can clear the tool page so that all the values are reset to zero. The image on the right shows what happens after clear of a program in the LightSpeed

The LightSpeed control needs these values to be filled out in order to work properly.

So you can either enter data manually, or load a good Tool setup into this page.

Lightspeed toolpage zeros.png
Lightspeed tools page setup.png

SOLUTION 3: Be sure the YBC Page CENTERLINE RADIUS Values Match the TOOL Page Values

Also, it is important that the centerline radius value in the YBC page matches the radius value in the TOOL page.

In the YBC page, be sure that the radius value in the radius box matches the radius value at the top of the die icon.

In the image example, the centerline radius value is ZERO, but the tools are setup for 1.875". This will cause the Bend Die value in the corresponding cell of the FULL view to turn red.

Lightspeed ybcpage clr zero closeup.png

Lightspeed ybcpage clr zero.png

Other Pages