Difference between revisions of "CNC Bender v12-20100414"
(5 intermediate revisions by one user not shown) | |||
Line 16: | Line 16: | ||
__TOC__ | __TOC__ | ||
+ | |||
+ | ===[[image:Check.jpg|25px]] ENHANCED - Benderlink Changes START Position Adjustment=== | ||
+ | <table> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | Benderlink is enhanced to correctly change the START position of the carriage during correction if that feature is switched on. | ||
+ | </td> | ||
+ | <td> | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | </td> | ||
+ | <td> | ||
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
===[[image:Check.jpg|25px]] REPAIRED - Benderlink Database Transfer Setup Clear=== | ===[[image:Check.jpg|25px]] REPAIRED - Benderlink Database Transfer Setup Clear=== | ||
Line 63: | Line 81: | ||
If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up. This has been resolved. | If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up. This has been resolved. | ||
</td> | </td> | ||
+ | <td> | ||
+ | </td> | ||
+ | </tr> | ||
+ | |||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | </td> | ||
+ | <td> | ||
+ | </td> | ||
+ | </tr> | ||
+ | </table> | ||
+ | |||
+ | ===[[image:Check.jpg|25px]] REPAIRED - Automatic Feed Adjustment During Part Load=== | ||
+ | <table> | ||
+ | <tr valign=top> | ||
+ | <td width=300> | ||
+ | The automatic feed adjustment feature works by advising operators that incoming part data was from another bender with a different bed length. We discovered that two of the Tool page options were not being changed properly. This is corrected.</td> | ||
<td> | <td> | ||
</td> | </td> |
Latest revision as of 14:28, 16 April 2010
|
Contents |
ENHANCED - Benderlink Changes START Position Adjustment
Benderlink is enhanced to correctly change the START position of the carriage during correction if that feature is switched on. |
|
REPAIRED - Benderlink Database Transfer Setup Clear
The CNC Bender database was corrupted when Benderlink users pressed the "Apply and Close" button without first having made a correction. The result was a CNC Bender setup that would cause major issues in CNC Bender. |
|
REPAIRED - Single Radius Carriage Shifting
Single radius carriage shifting is now re-enabled in this version. |
|
REPAIRED - Direct Axes Jog Buttons Stick Down
If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up. This has been resolved. |
|
REPAIRED - Automatic Feed Adjustment During Part Load
The automatic feed adjustment feature works by advising operators that incoming part data was from another bender with a different bed length. We discovered that two of the Tool page options were not being changed properly. This is corrected. | |
Other Pages
- Back to CNC Bender
- Back to CNC Bender Software Updates
- See CNC Bender General Information
- See Teach Mode
- See Custom Commands