Difference between revisions of "Wiring: Finding 120 VAC in a CNC Bender Lite operator station"
From ATTWiki
(→STEP 2: Find the 120VAC) |
(→STEP 4: Attach the Spare Wire to the Neutral) |
||
(9 intermediate revisions by one user not shown) | |||
Line 1: | Line 1: | ||
==About== | ==About== | ||
+ | <table> | ||
+ | <tr valign=top> | ||
+ | <td width=200> | ||
+ | |||
Some original CNC Bender LiteControl operator stations use 24 VDC to power the computer. However, the newer Pro-face units sometimes come with 100-220VAC power supply requirements.<br> | Some original CNC Bender LiteControl operator stations use 24 VDC to power the computer. However, the newer Pro-face units sometimes come with 100-220VAC power supply requirements.<br> | ||
<br> | <br> | ||
This document shows where to find 120 VAC in these operator stations.<br><br> | This document shows where to find 120 VAC in these operator stations.<br><br> | ||
+ | </td> | ||
+ | |||
+ | <td> | ||
<table cellpadding="15"> | <table cellpadding="15"> | ||
<tr> | <tr> | ||
Line 13: | Line 20: | ||
There can be high voltages and currents of electricity flowing through the electrical panel. | There can be high voltages and currents of electricity flowing through the electrical panel. | ||
</font></td></tr></table> | </font></td></tr></table> | ||
+ | |||
+ | </td> | ||
+ | |||
+ | </tr> | ||
+ | </table> | ||
+ | |||
<br><br> | <br><br> | ||
Line 34: | Line 47: | ||
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
− | <td width= | + | <td width=300> |
You will find 120VAC on the back of the E-Stop button. (Test this with a multimeter.) The terminal with constant power is usually the right side. | You will find 120VAC on the back of the E-Stop button. (Test this with a multimeter.) The terminal with constant power is usually the right side. | ||
Line 45: | Line 58: | ||
*Insert the pin in the Pro-face L terminal. | *Insert the pin in the Pro-face L terminal. | ||
<br><br> | <br><br> | ||
− | [[image:120vac_wire_to_estop_closeup.jpg| | + | [[image:120vac_wire_to_estop_closeup.jpg|300px]] |
</td> | </td> | ||
Line 61: | Line 74: | ||
<table> | <table> | ||
<tr valign=top> | <tr valign=top> | ||
− | <td width= | + | <td width=200> |
− | *A spare wire is coiled in the operator station | + | |
− | *Trace this wire back to the electrical panel | + | *A spare wire is usually coiled in the operator station<br><br> |
+ | *Trace this wire back to the electrical panel<br><br> | ||
*Attach the other end of this cable to a Neutral (you will need to find where you can tap into the Neutral in the panel. There will be a connection on the terminal strip at the bottom of the panel.) | *Attach the other end of this cable to a Neutral (you will need to find where you can tap into the Neutral in the panel. There will be a connection on the terminal strip at the bottom of the panel.) | ||
+ | |||
</td> | </td> | ||
Line 77: | Line 92: | ||
==STEP 4: Attach the Spare Wire to the Neutral== | ==STEP 4: Attach the Spare Wire to the Neutral== | ||
− | + | <table> | |
− | + | <tr valign=top> | |
+ | <td width=200> | ||
+ | *Attach a terminal pin to end of the spare wire in the operator station.<br><br> | ||
+ | *Attach the spare wire to the Neutral terminal in the | ||
+ | <br><br> | ||
+ | |||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | </td> | ||
+ | |||
+ | </tr> | ||
+ | </table> | ||
+ | |||
+ | |||
+ | |||
+ | ==STEP 5: Attach the a Ground Wire== | ||
+ | <table> | ||
+ | <tr valign=top> | ||
+ | <td width=200> | ||
+ | |||
+ | *Attach a ground wire to the ground terminal at the Pro-face | ||
+ | |||
+ | <br><br> | ||
+ | |||
+ | </td> | ||
+ | |||
+ | <td> | ||
+ | </td> | ||
+ | |||
+ | </tr> | ||
+ | </table> | ||
==Tools/Parts Needed== | ==Tools/Parts Needed== |
Latest revision as of 18:03, 19 December 2009
Contents |
About
STEP 1: Open the operator station front cover
This cover uses a hinge at the bottom, so you can swing it down for work inside the operator station.
|
STEP 2: Find the 120VAC
You will find 120VAC on the back of the E-Stop button. (Test this with a multimeter.) The terminal with constant power is usually the right side.
|
STEP 3: Locate a Spare Wire that Runs Through the Flexible Conduit
|
STEP 4: Attach the Spare Wire to the Neutral
|
STEP 5: Attach the a Ground Wire
|
Tools/Parts Needed
14 Gauge THHN stranded wire |
|
Vinyl Insulate Terminal Pin for 14 gauge wire (See 159-1617 Kobiconn Terminals Pin Blue 16-14 at Mouser.com) |
|
Possibly a jumper bar (Automationdirect.com DINnectors DN-82J10) |
|
Crimper for terminal pins, screw drivers, diagonal cutters for cutting the jumper bar |
Other Pages
- Back to the CNC Bender Page
- Back to the CNC Bender Technical Notes Page