Difference between revisions of "VTube Communication with YLM Benders"

From ATTWiki
Jump to: navigation, search
(Follow these steps at VTube-LASER to Correct a YLM Bender)
(VTube-STEP and VTube-LASER Support for YLM Benders)
 
(20 intermediate revisions by one user not shown)
Line 10: Line 10:
 
</tr>
 
</tr>
 
</table>
 
</table>
 
__NOTOC__
 
  
  
Line 18: Line 16:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
[[VTube-STEP]] can export Supravision data to YLM benders.<br><br>   
+
[[VTube-STEP]] can export Supravision data to YLM benders using a standard network connection.<br><br>   
[[VTube-LASER]], the version of VTube that connects to a FARO measuring center arm, can send measured data to the YLM control for corrections.<br><br>
+
[[VTube-LASER]], the version of VTube that connects to a measuring center arm, can send measured data to the YLM control for corrections.<br><br>
[[image:faro_scanner_v6.png|300px]]
+
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
Line 27: Line 24:
 
</tr>
 
</tr>
 
</table>
 
</table>
 +
 +
 +
__TOC__
  
 
==The Principles for Sending Data to YLM==
 
==The Principles for Sending Data to YLM==
Line 39: Line 39:
  
 
# In VTube: Measure a part.<br><br>
 
# In VTube: Measure a part.<br><br>
# In VTube: Save the measured part data to a Supravison file.<br><br>
+
# In VTube: Save the MEASURED part data (not the MASTER part data) to a Supravison file using the File/Export feature in the Measured menu.<br><br>
 
# In YLM Control: Load the same Supravision file into the control using the CORRECTION button.<br><br>
 
# In YLM Control: Load the same Supravision file into the control using the CORRECTION button.<br><br>
 
</td>
 
</td>
Line 83: Line 83:
 
===Follow these steps at VTube-LASER to Send a NEW TUBE SETUP to a YLM Bender===
 
===Follow these steps at VTube-LASER to Send a NEW TUBE SETUP to a YLM Bender===
 
<table>
 
<table>
 +
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
 
'''STEP 1'''<br>
 
'''STEP 1'''<br>
Switch to the MASTER TUBE window and press the FILE tab.<br><br>
+
Switch to the MASTER TUBE window and press the EXPORT tab.<br><br>
 
'''STEP 2'''<br>
 
'''STEP 2'''<br>
Save the Supravision file.<br><br>
+
Choose "Export to Supravision file" in the pulldown menu.<br><br>
 +
</td>
 +
<td width=400>
 +
[[image:vtube-laser-2.9.14_SaveMasterSupravisionData.png|500px]]<br><br>
 +
</td>
 +
</tr>
 +
 
 +
<tr valign=top>
 +
<td width=300>
 
'''STEP 3'''<br>
 
'''STEP 3'''<br>
 +
Choose the appropriate data options, then press "Save to Supravision File."<br><br>
 +
The Path Manager will display and allow you to select the correct bender path.<br><br>
 +
'''STEP 4'''<br>
 
Move to the YLM control and follow the steps below to import the new data.<br><br>
 
Move to the YLM control and follow the steps below to import the new data.<br><br>
[[image:vtube-laser-1.96_SupravisionExportMenu_Master.png|500px]]<br><br>
 
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-laser-1.96_SaveMasterSupravisionData.png|500px]]<br><br>
+
[[image:vtube-laser-2.9.14_SupravisionExportMenu_Master.png|500px]]<br><br>
 
+
 
</td>
 
</td>
 
</tr>
 
</tr>
 +
 +
 
</table>
 
</table>
  
Line 183: Line 195:
 
<td width=600>
 
<td width=600>
 
The connection the bender is made with standard network connection, and a shared folder location between the VTube computer and the operator station computer.<br><br>
 
The connection the bender is made with standard network connection, and a shared folder location between the VTube computer and the operator station computer.<br><br>
The YLM control handles corrections differently than any other control.  This is how it is unique:<br><br>
+
The YLM control handles corrections differently than most other controls.  This is how it is unique: For a CORRECTION, the YLM takes in VTube MEASURED Supravision LRA data.  To make a correction to a YLM bender, it is important to send ONLY the data for the MEASURED part - not the MASTER, and not CORRECTION data inside the Bender Setup menu.  For the YLM bender, you never have to enter the Bender Setup menu.<br><br>
 
+
* First, for a CORRECTION, the YLM takes in VTube MEASURED Supravision LRA data.  To make a correction to a YLM bender, it is important to send ONLY this data.  The standard correction process will not work with the YLM.<br><br>
+
* Second, the YLM uses the correction in the opposite way in its standard setup when taking in the MEASURED data and comparing it to its MASTER or NOMINAL data.  For example, if the Measured data shows 1 degree overbent, then the YLM correction procedure will send that bend one MORE degree.
+
<br><br>
+
===Handling Opposite Corrections===
+
There are two ways to overcome the opposite correction problem:
+
 
+
1 - Use a special INVERSION checkbox in the VTube Supravision Export menu.  Only use this inversion switch when sending measured data for correction.<br><br>
+
 
+
2 - Have the YLM technician change the internal low level setting in the YLM control that makes the correction be apply in the normal way.<br><br>
+
 
+
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
Line 206: Line 207:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
 +
Measure the tube.<br><br>
 
Switch to the MEASURED TUBE window and press the FILE tab.<br><br>
 
Switch to the MEASURED TUBE window and press the FILE tab.<br><br>
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:VTube-Laser-1.96_SaveMeasuredTubeData.png|500px]]<br><br>
+
[[image:VTube-Laser-2.9.14_SaveMeasuredTubeData.png|500px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 218: Line 220:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
Most YLM benders use the pure MEASURED data for corrections. However, some YLM benders need the MEASURED data changed into the CORRECTED data - and the CORRECTIONS are always made based on the MASTER data (not the existing data in the bender).  We call this "YBC Correction Inversion".<br><br>
+
Save the Measured data to a Supravision file.<br><br>
If you find that the corrections move in the wrong direction on a YLM, then check the inversion check boxThe inversion check box will only display if VTube knows you are saving MEASURED data to a Supravision file.<br><br>
+
 
 +
=====About the Options=====
 +
INVERT ROTATIONS: VTube-LASER thinks as CCW is a positive rotation viewed from the front of the bender. However, some YLM benders view the positive rotation as a clockwise move. If the YLM bender rotates positive in the clockwise direction, then put a check in the "Additive Invert the Rotation Values in the LRA Data for CW Positive" checkbox. (Additive Invert means to multiply all the numbers by -1.)<br><br>
 +
 
 +
INVERT LRA DATA: Most newer YLM benders use the pure MEASURED data for correctionsHowever, some older YLM benders need the MEASURED data to be converted with a special "Invert the Measured LRA Output for YLM Control Corrections" option. We don't recommend that you use this option unless we tell you that it is needed. (What it does is complicated - so we'll spare you the details.)<br><br>
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:vtube-laser-1.96_SupravisionExportMenu.png|500px]]<br><br>
+
[[image:vtube-laser-2.9.14_SupravisionExportMenu.png|500px]]<br><br>
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 231: Line 237:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
Save the Supravision file.<br><br>
+
Move to the YLM control and follow the steps below to import the correction.
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
Line 238: Line 244:
 
</table>
 
</table>
  
====STEP 4====
+
<br><br>
 +
 
 +
===Follow these steps at the YLM CONTROL to import the measured data from VTube-LASER===
 +
 
 +
====STEP 1====
 
<table>
 
<table>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
Move to the YLM control and follow the steps below to import the correction.
+
In the YLM YBC menu, click on CORRECTION.<br><br>
 +
Note: This button can be disabled on some controls and must be enabled in the setup.  Contact Joe Seibel ([email protected]) of this button is disabled so that he can give you instructions for enabling the feature.
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
 +
[[image:ylm_ybc_correction_button.png|300px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
 
</table>
 
</table>
  
<br><br>
+
====STEP 2====
 
+
===Follow these steps at the YLM CONTROL to import the measured data from VTube-LASER===
+
 
+
 
<table>
 
<table>
 
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
'''STEP 1'''<br>In the YLM YBC menu, click on CORRECTION.<br><br>
+
Search for and select the $$$ file that was created by VTube-LASER.<br><br>
Note: This button can be disabled on some controls and must be enabled in the setup.  Contact Joe Seibel ([email protected]) of this button is disabled so that he can give you instructions for enabling the feature.
+
 
+
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
[[image:ylm_ybc_correction_button.png|300px]]
 
 
</td>
 
</td>
 
</tr>
 
</tr>
 +
</table>
  
 +
====STEP 3====
 +
<table>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
'''STEP 2'''<br>Search for and select the $$$ file that was created by VTube-LASER.<br><br>
+
Select COMPARE to bring the data into the YLM control.  The COMPARE button will only display when a file is selected.
'''STEP 3'''<br>Select COMPARE to bring the data into the YLM control.  The COMPARE button will only display when a file is selected.
+
 
<br><br>'''NOTE: DO NOT press the IMPORT button for corrections.  Pressing IMPORT will make the correction data the nominal data - which would be incorrect.'''<br><br>
 
<br><br>'''NOTE: DO NOT press the IMPORT button for corrections.  Pressing IMPORT will make the correction data the nominal data - which would be incorrect.'''<br><br>
 
</td>
 
</td>
Line 276: Line 283:
 
</td>
 
</td>
 
</tr>
 
</tr>
 +
</table>
  
 +
====STEP 4====
 +
<table>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
'''STEP 4'''<br>Press the menu close button in the lower right corner.<br><br>
+
Press the menu close button in the lower right corner.<br><br>
 
</td>
 
</td>
 
<td width=400>
 
<td width=400>
Line 285: Line 295:
 
</td>
 
</td>
 
</tr>
 
</tr>
 
 
 
</table>
 
</table>
  

Latest revision as of 19:36, 24 August 2021

YLMcncbender.jpg

YLMlogo.jpg


VTube-STEP and VTube-LASER Support for YLM Benders

VTube-STEP can export Supravision data to YLM benders using a standard network connection.

VTube-LASER, the version of VTube that connects to a measuring center arm, can send measured data to the YLM control for corrections.

VTubeToYLM.jpg


Contents


The Principles for Sending Data to YLM

  • This method doesn't use the automated Supravision Network protocol - but it does require that the VTube-LASER operator saves Supravision files in a network location shared with the YLM control.

  • YLM communications never requires that VTube-LASER perform a RECALL to update the pre-correction bender data in VTube-LASER BENDER SETUP, because, unlike other benders, the YLM control (not VTube-LASER) applies the corrections from the measured data it loads into the YLM control.

The process works like this:

  1. In VTube: Measure a part.

  2. In VTube: Save the MEASURED part data (not the MASTER part data) to a Supravison file using the File/Export feature in the Measured menu.

  3. In YLM Control: Load the same Supravision file into the control using the CORRECTION button.

Basic Network Setup

For networking VTube-LASER computer to a YLM bender control, setup a method where one computer can see where the other computer has placed the files. If your bender control cannot log into the company network for read/write privileges, then just share a folder on the YLM operator station hard drive, and allow VTube to save the measured data in that folder.



Using VTube-LASER to send NEW MASTER Data to YLM Benders

The connection the bender is made with standard network connection, and a shared folder location between the VTube computer and the operator station computer.

For a NEW TUBE, the YLM takes in VTube MASTER Supravision LRA data in a Supravision file.



Follow these steps at VTube-LASER to Send a NEW TUBE SETUP to a YLM Bender

STEP 1
Switch to the MASTER TUBE window and press the EXPORT tab.

STEP 2
Choose "Export to Supravision file" in the pulldown menu.

Vtube-laser-2.9.14 SaveMasterSupravisionData.png

STEP 3
Choose the appropriate data options, then press "Save to Supravision File."

The Path Manager will display and allow you to select the correct bender path.

STEP 4
Move to the YLM control and follow the steps below to import the new data.

Vtube-laser-2.9.14 SupravisionExportMenu Master.png

Follow these steps at the YLM CONTROL to import the MASTER data from VTube-LASER

STEP 1

In the YLM control, clear the YBC data. (Note:Clearing is optional. It is not always necessary - but seems to keep data from overlapping between older and newer setups.)

YLM YBC Screen.png

STEP 2


In the YLM YBC menu, click on CORRECTION.

Note: This button can be disabled on some controls and must be enabled in the setup. Contact Joe Seibel ([email protected]) of this button is disabled so that he can give you instructions for enabling the feature.

Ylm ybc correction button.png

STEP 3

In the lower right corner of the screen, select the drive and path then explore for and select the $$$ file that was created by VTube-LASER.

YLM Import Screen.jpg

STEP 4

In the YLM YBC menu, click on IMPORT. (Do not click "COMPARE" - as that is for corrections.)

YLM YBC NewImport.png

STEP 5

Press the Exit menu close button in the lower right corner of the screen.

YLM YBCCorrections exit.png

STEP 6

In order to exit the YBC screen, you might need to double tap on the teach mode button in order to turn on teach mode. Then double tap on the sequences icon on the top of the sequences column. Reset the sequences.

YLMTeachModeAndSequence.png




VTube-LASER CORRECTION Steps for YLM Benders

The connection the bender is made with standard network connection, and a shared folder location between the VTube computer and the operator station computer.

The YLM control handles corrections differently than most other controls. This is how it is unique: For a CORRECTION, the YLM takes in VTube MEASURED Supravision LRA data. To make a correction to a YLM bender, it is important to send ONLY the data for the MEASURED part - not the MASTER, and not CORRECTION data inside the Bender Setup menu. For the YLM bender, you never have to enter the Bender Setup menu.

Follow these steps at VTube-LASER to Correct a YLM Bender

STEP 1

Measure the tube.

Switch to the MEASURED TUBE window and press the FILE tab.

VTube-Laser-2.9.14 SaveMeasuredTubeData.png

STEP 2

Save the Measured data to a Supravision file.

About the Options

INVERT ROTATIONS: VTube-LASER thinks as CCW is a positive rotation viewed from the front of the bender. However, some YLM benders view the positive rotation as a clockwise move. If the YLM bender rotates positive in the clockwise direction, then put a check in the "Additive Invert the Rotation Values in the LRA Data for CW Positive" checkbox. (Additive Invert means to multiply all the numbers by -1.)

INVERT LRA DATA: Most newer YLM benders use the pure MEASURED data for corrections. However, some older YLM benders need the MEASURED data to be converted with a special "Invert the Measured LRA Output for YLM Control Corrections" option. We don't recommend that you use this option unless we tell you that it is needed. (What it does is complicated - so we'll spare you the details.)

Vtube-laser-2.9.14 SupravisionExportMenu.png

STEP 3

Move to the YLM control and follow the steps below to import the correction.



Follow these steps at the YLM CONTROL to import the measured data from VTube-LASER

STEP 1

In the YLM YBC menu, click on CORRECTION.

Note: This button can be disabled on some controls and must be enabled in the setup. Contact Joe Seibel ([email protected]) of this button is disabled so that he can give you instructions for enabling the feature.

Ylm ybc correction button.png

STEP 2

Search for and select the $$$ file that was created by VTube-LASER.

STEP 3

Select COMPARE to bring the data into the YLM control. The COMPARE button will only display when a file is selected.

NOTE: DO NOT press the IMPORT button for corrections. Pressing IMPORT will make the correction data the nominal data - which would be incorrect.

YMC YBC Correction CompareButton.png

STEP 4

Press the menu close button in the lower right corner.

YLM YBCCorrections exit.png

Shutdown to Edit the Windows Setup

To shutdown the YLM software to configure Windows settings:

  1. Press the Shutdown button.

  2. Press "NO" for shutdown.

  3. Type "12345" and OK in the numeric keypad.

  4. YLM will close without shutting down the computer.






Other Pages