Difference between revisions of "VTube-STEP v1.94"

From ATTWiki
Jump to: navigation, search
(→‎25px CRITICAL ENHANCEMENT: Cylinder Centerline Calculation in Math Engine Improved Significantly)
(→‎25px CRITICAL ENHANCEMENT: Cylinder Centerline Calculation in Math Engine Improved Significantly)
Line 25: Line 25:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
−
'''STARTS WITH A MUCH SMALLER 10th of a MICRON PROJECTION TOLERANCE'''<br><br>
+
'''THE STARTING CENTERLINE CALCULATION PROJECTION TOLERANCE IS NOW REDUCED to a 10th of a MICRON'''<br><br>
 
To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with an much smaller projection tolerance at a 10th of a micron (0.0001 mm, or 0.000003937 inches).<br><br>
 
To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with an much smaller projection tolerance at a 10th of a micron (0.0001 mm, or 0.000003937 inches).<br><br>
 
If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution.<br><br>
 
If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution.<br><br>
Line 37: Line 37:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
−
'''CENTERLINE CALCULATION FOR ROUGH CYLINDERS SIGNIFICANTLY ENHANCED'''<br><br>
+
'''THE CENTERLINE CALCULATION for ROUGH CYLINDERS IS SIGNIFICANTLY ENHANCED'''<br><br>
 
Sometimes VTube is asked to calculate the centerline of a cylinder that's not really a cylinder.  VTube can handle approximate cylinders much better in this version than in previous versions.<br><br>  This includes projections for cylinders with forms like coping and bulges or holes - or just inaccurate surfaces.</td>
 
Sometimes VTube is asked to calculate the centerline of a cylinder that's not really a cylinder.  VTube can handle approximate cylinders much better in this version than in previous versions.<br><br>  This includes projections for cylinders with forms like coping and bulges or holes - or just inaccurate surfaces.</td>
 
<td width=500>
 
<td width=500>

Revision as of 00:58, 1 September 2014

Vtube-step logo.jpg

Revision 1.94

Vtube-step-1.93 screenshot.png




Check.jpg CRITICAL ENHANCEMENT: Cylinder Centerline Calculation in Math Engine Improved Significantly

THE STARTING CENTERLINE CALCULATION PROJECTION TOLERANCE IS NOW REDUCED to a 10th of a MICRON

To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with an much smaller projection tolerance at a 10th of a micron (0.0001 mm, or 0.000003937 inches).

If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution.

The final projection tolerance used is stored in the Collection grid so that you can view the result at any time after a calculation.

Vtube-step-1.94 projtolerance tenth micron.png

THE CENTERLINE CALCULATION for ROUGH CYLINDERS IS SIGNIFICANTLY ENHANCED

Sometimes VTube is asked to calculate the centerline of a cylinder that's not really a cylinder. VTube can handle approximate cylinders much better in this version than in previous versions.

This includes projections for cylinders with forms like coping and bulges or holes - or just inaccurate surfaces.

Vtube-step-1.94 coping handled.png

Check.jpg NEW: Trim Surface Datum for Trimming or Extending End Lengths

VTube-STEP now allows for different kind of Trim Surfaces now. Older versions only allow for the centroid (average XYZ point) of all points in a solid used to trim.

Vtube-step-1.94 surface trim datum.png

  • CENTROID POINT - Trim/Extend to the average centroid point in the surface cloud.

Vtube-step surface points centroid.png

  • FURTHEST POINT - Trim/Extend to the furthest point in the cloud from the midpoint of the tube centerline.

Vtube-step-1.94 trim surface furthest point coping.png

Vtube-step surface points furthest.png

  • NEAREST POINT - Trim/Extend to the nearest point in the cloud from the midpoint of the tube centerline.

Vtube-step surface points nearest.png

Check.jpg NEW: Add Collection Grid Properties Column and Edit Datum Menu

The new properties column allows for new options to accompany each of the collected objects.

The properties cells will show the TrimSurf datum type.

Right click on any TrimSurf row, then choose Edit Trim Surface Datum to enter this menu (below):

Vtube-step-1.94 edit trimsurf datum type.png

Vtube-step-1.94 collection grid properties.png

Check.jpg ENHANCED: DEFAULT Projection Tolerance for Centerline Calculation is Removed from Interface

Since the STEP mode calculation engine completely automates the Projection Tolerance, there is no longer a need for the user to set this value.

It is removed from above the Collection grid.

Vtube-step-1.94 collection header no projtolerance.png


Check.jpg Other Changes

  • Fixed a bug in the Recent Folder data in the Quick Load Dialog for project files and import files.


  • The Alpine M4 export was fixed: The radius level is now included in the YBC data. The last C value (Length) is set to ZERO in the YBC columns.

Other Pages

Retrieved from "http://www.advancedtubular.wiki/index.php?title=VTube-STEP_v1.94&oldid=25343"