Difference between revisions of "VTube-STEP v1.77.3"

From ATTWiki
Jump to: navigation, search
(25px NEW: Adjustable Import/Export Interface with New Choices)
(25px NEW: Added Several New fields in Part Setup)
Line 54: Line 54:
  
  
===[[image:Check.jpg|25px]] NEW:  Added Several New fields in Part Setup===
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
Customers requested several new fields in the Part Setup menu - so we added them:<br><br>
 
These new fields are available for the reports templates, and they are saved the VTP project file.
 
</td>
 
<td width=300>
 
[[image:vtube-pro_1_76.4_PartSetup.jpg|300px]]
 
</td>
 
</tr>
 
</table>
 
  
  

Revision as of 03:13, 8 August 2012

Vtube-step logo.jpg

Revision 1.77.3

Vtube-step 1.77.3a.jpg



Check.jpg UPDATED: View Orientation Control

The View Orientation Control has new choices with graphics icons of each axes orientation.

You can click on the button or the image to find a new orientation.

Vtube 1.77.3 vieworientation.jpg

Check.jpg NEW: End Lengths Change in Diameter Model with End Adjustment Length Values

When the A-End or B-End Adjustment Lengths change, then the diameter model lengths change automatically at the next redraw. This does not change the centerline end point location.

Vtube 1.77.3 EndLengthShortened.jpg

Check.jpg REPAIR: Cut Length Calculation with End Adjustments

The End Length Adjustments were doubled in the Cut Length calculation. This is repaired in this version.

Vtube endlength cutlength partsetup.jpg



Check.jpg NEW: New End Length Adjustment Fields

These new fields allow you to dynamically adjust the end lengths during calculation of the bender data LENGTH columns.

These values act like the TubeCalc material end length fields - and allows that data to be imported.

Vtube-step end length adjustment fields.jpg

Check.jpg ENHANCED: Changed End Trim Offset Field Names

The original End Trim Offset field names were changed by default to "Solid Model Offset" to reflect how these values are used in VTube.

These values adjust the end point location relative to the solid model when the centerline is calculated from the solid model.

Vtube-step end solid model offsets.jpg

Check.jpg NEW: Reset Origin to Zero in XYZ Data

Now you can reset the origin in the XYZ data to ZERO in VTube-STEP.

Vtube-step reset origin.jpg

Check.jpg REPAIR: TubeCalc Project File Linear Units Import Properly

Linear units are now always properly imported into VTube from TubeCalc files.

Previous versions would sometimes improperly interpret the Inch or Millimeter setting in the TubeCalc file.

Check.jpg ENHANCED: The Linear Units Switches to the Import File Units

VTube now always switches to the linear units used in the imported TubeCalc, Solid Edge, or Supravision file.


Check.jpg ENHANCED: TubeCalc Project Imports Include More Values

The following values were added to TubeCalc imports in this version:

From TubeCalcTo VTube
Customer NameSmall right green arrow.pngCustomer
Material NameSmall right green arrow.pngMaterial Spec
UserSmall right green arrow.pngAuthor
Material Offset 1Small right green arrow.pngA-End Length Adjust
Material Offset 2Small right green arrow.pngB-End Length Adjust
Measuring Center Offset ASmall right green arrow.pngA-End Measured Offset
Measuring Center Offset BSmall right green arrow.pngB-End Measured Offset




Check.jpg FIXED: Projection Tolerances Now Change Units Properly

The projection tolerance now handles a change in linear units properly.

Projection tolerances allow VTube to know how precise it must be to qualify a projection intersection as successful. Some models have less precise surfaces - so the tolerance needs to be increased for a successful calculation of centerline.

Vtube v1.77 projectiontoleranceedit.jpg

Check.jpg ENHANCED: Report Formatting Updated

The report formatting is updated with larger and bolder tiles.

Vtube v1.77 reportformat.jpg

Other Pages