Difference between revisions of "VTube-LASER v2.9.15"

From ATTWiki
Jump to: navigation, search
(25pxFIX - IMPORTANT UPDATE for IMPORTING 180-DEGREE BENDS)
(25pxFIX - IMPORTANT UPDATE for IMPORTING 180-DEGREE BENDS)
Line 46: Line 46:
 
<br><br>
 
<br><br>
  
==[[image:Check.jpg|25px]]FIX - IMPORTANT UPDATE for IMPORTING 180-DEGREE BENDS ==
+
==[[image:Check.jpg|25px]]FIX - IMPORTANT UPDATE for IMPORTING and MEASURING 180-DEGREE BENDS ==
  
 
<table cellpadding=10 width=1200>
 
<table cellpadding=10 width=1200>

Revision as of 22:03, 8 October 2018

Vtube-laser logo 1.96.png


Revision 2.9.15

Release Date: October 8, 2018
Current Build: 8


Vtube-laser v2.7 screenshot.png

Contents


Check.jpgNEW - END LENGTH FILTER - SHIFTS LENGTH CORRECTIONS BETWEEN A-END and B-END

Vtl v2.9.15 EndLengthFilter Graphic.png

VTube-LASER now allows you to shift the total correction between ends using the End Length Filter menu in Bender Setup.

This feature resembles the End Tag feature in the original Supravision software.

It is particularly useful for any application that starts with large volumes of pre-cut tubing. There is no option for easily changing the tube length - so it is important to allow VTube-LASER to spread the total length change during the correction process to the front straight, the back straight, or both evenly.

Vtl 2.9.15 EndLengthFilter.png



Check.jpgFIX - IMPORTANT UPDATE for IMPORTING and MEASURING 180-DEGREE BENDS

If you import models with 180-degree bends, then you will use the Split Bend COLLECTION feature in VTube-STEP. If you measure 180-degree bends, then you will use the Split Bend MEASURE feature in VTube-LASER.

Both of these features use the same Split Bend math logic.

If you use the Split Bend logic in VTube, then this update is critical for you because it addresses an issue we discovered during some research into Split Bend measuring issues with a customer.

The problem we found could cause the centerline of the Split Bend construction to be short by 0.020 inches (0.5 mm).

Vtl v2.9.15 splitbend import.png



Check.jpgFIXED - CLEARING ALL CUT PLANES from the CUT PLANE LIST NOW WORKS

We discovered that, when you delete the entire list of Cut Planes, VTube-LASER will most likely bring at least one of them back. (They are not cleared permanently.)

This has been fixed so that cleared Cut Planes never reappear.

Multiplecutplanes.png



Check.jpg NEW - REPORT ABSOLUTE CONRAC CORRECTIONS

VTube-LASER can now report absolute CONRAC bender corrections using new HTML report template values.

Conracbender.png

The two new tokens to use inside the html tags are:

  • <vtube_val>Array_Lcor_Absolute</vtube_val>
  • <vtube_val>Array_Rcor_Absolute</vtube_val>

Vtl 2.9.14 conrac correction report.png



Check.jpg NEW - RONIKolli7 Bender Simulator ASCII XYZ File Import

3slogo.png

VTube-STEP mode can now import RONIKolli7 bender simulator ASCII XYZ files.

That data imported includes:

  • Part Number (filename)
  • Material Note
  • Diameter
  • Wall Thickness
  • XYZ + centerline Radius



VTube also calculates the default radius and the Cut Length during the import.

Vtl 2.9.14 ronikolli7 ascii xyz.png



Check.jpg OTHER CHANGES

  • Probe point throughput is potentially 2.5 faster than in previous versions.



Other Pages