Difference between revisions of "VTube-LASER v1.75.1"

From ATTWiki
Jump to: navigation, search
(25px NEW: "Pull Arm From Resting Position" Message)
(25px FIX: Previous Move During Remeasure)
 
(3 intermediate revisions by one user not shown)
Line 40: Line 40:
 
</table>
 
</table>
  
 
+
===[[image:Check.jpg|25px]] ENHANCED: Removed the Default Radius Setup Message===
 
+
 
+
 
+
 
+
 
+
 
+
 
+
===[[image:Check.jpg|25px]] NEW: Separate Cylinder Fit Tolerances for LONG and SHORT Cylinders===
+
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
VTube now has a second set of tolerances for shorter straights.   This allows for looser tolerances on shorter straights without producing an error message.
+
The message that says that VTube will automatically set the default radius to 1.5 times the diameter no longer displays as it serves no useful purpose.</td>
<br><br>
+
</td>
+
 
<td width=300>
 
<td width=300>
[[image:LongAndShortCylinderFitSetup.jpg|300px]]
 
 
</td>
 
</td>
 
</tr>  
 
</tr>  
</table>
 
 
 
 
 
===[[image:Check.jpg|25px]] Other Changes===
 
<table cellpadding=10>
 
 
<tr valign=top>
 
<td width=300>
 
A new tolerance is added for surface point diameter check.
 
</td>
 
<td width=300>
 
</td>
 
</tr>
 
</table>
 
 
 
<table cellpadding=10>
 
 
<tr valign=top>
 
<td width=300>
 
The current arm firmware is now read and used by VTube to determine how to handle the arm during Scanner Control changes.
 
</td>
 
<td width=300>
 
[[image:ArmFirmware.jpg|300px]]
 
</td>
 
</tr>
 
</table>
 
 
<table cellpadding=10>
 
 
<tr valign=top>
 
<td width=300>
 
For high-precision end scans, new end-scan techniques are recommended in the VTube-LASER manual.<br><br>
 
* See [[End-Scan Using the Scissor Motion]]
 
* See [[End-Scan Using the End Wall]]
 
* See [[End-Scan Using End Targets]]
 
 
</td>
 
<td width=300>
 
[[image:EndScanAfterTarget.jpg|300px]]
 
</td>
 
</tr>
 
</table>
 
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
The VTube SVNET protocol now knows how to handle leftover communications files if they are present.
 
</td>
 
<td width=300>
 
</td>
 
</tr>
 
</table>
 
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
VTube can now save Supravision data to multiple file extension types: $$$, SV, or S2B
 
</td>
 
<td width=300>
 
</td>
 
</tr>
 
</table>
 
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
VTube-LASER now takes in scanned points faster than before.</td>
 
<td width=300>
 
</td>
 
</tr>
 
</table>
 
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
VTube-LASER installation now allows for installing either MM or INCH default setups.</td>
 
<td width=300>
 
</td>
 
</tr>
 
</table>
 
 
<table cellpadding=10>
 
<tr valign=top>
 
<td width=300>
 
Default setups were fine-tuned in VTube-LASER so that VTube works faster.</td>
 
<td width=300>
 
</td>
 
</tr>
 
 
</table>
 
</table>
  
 
=Other Pages=
 
=Other Pages=
 
*Back to [[VTube-LASER]]
 
*Back to [[VTube-LASER]]

Latest revision as of 18:08, 3 February 2012

Vtube-laser logo.jpg

Revision 1.75.1

Back to VTube-LASER
Back to VTube-STEP

Vtube-laser 1 73.jpg


Check.jpg ENHANCEMENT: Added Page Numbers to Reports in Print Preview

VTube now shows the date, time, and page numbers at the bottom of print preview reports.

VTube-LASER Print Preview PageNumbers.jpg

Check.jpg FIX: Previous Move During Remeasure

There were circumstances where VTube would backup too many steps during a remeasure. This has been repaired.

Check.jpg ENHANCED: Removed the Default Radius Setup Message

The message that says that VTube will automatically set the default radius to 1.5 times the diameter no longer displays as it serves no useful purpose.

Other Pages