Difference between revisions of "VTube-LASER Cylinder Fit Tolerances"

From ATTWiki
Jump to: navigation, search
(Cylinder Centerlines Are Calculated from Cylinder Surface Points)
("How Well Does Centerline Fit the Cylinder Surface Points?")
Line 23: Line 23:
 
<tr>
 
<tr>
 
<td width=400>
 
<td width=400>
VTube-LASER uses surface points scanned with laser or measured with ball probes to calculate tube centerlines. Regular tube scans assume that the primitive shape to solve for is a cylinder.<br><br>
+
VTube-LASER uses surface points scanned with laser or measured with ball probes to calculate tube centerlines.<br><br>
 +
Regular tube scans assume that the primitive shape to solve for is a cylinder.<br><br>
 
When solving for a cylinder centerline, it's important to report the estimated accuracy of the calculation. The estimated accuracy helps us know how confident we can be in the calculation.<br><br>
 
When solving for a cylinder centerline, it's important to report the estimated accuracy of the calculation. The estimated accuracy helps us know how confident we can be in the calculation.<br><br>
 
</td>
 
</td>

Revision as of 17:28, 20 February 2017


Vtube-laser logo 1.96.png


Vtube-laser 1.89 mainscreen.png



"How Well Does Centerline Fit the Cylinder Surface Points?"

VTube-LASER uses surface points scanned with laser or measured with ball probes to calculate tube centerlines.

Regular tube scans assume that the primitive shape to solve for is a cylinder.

When solving for a cylinder centerline, it's important to report the estimated accuracy of the calculation. The estimated accuracy helps us know how confident we can be in the calculation.

Vtube-laser cylinder surfacepoints.png

The Cylinder Fit Data Window Reports How Well the Centerline Fits the Surface Data

After calculating a cylinder centerline from surface points, VTube-LASER also returns how well the centerline FITS the surface points of the cylinder.

VTube-LASER reports the accuracy of the centerline fit in the Cylinder Fit Data window. The values are deviations for...

  • RADIUS: Estimate the maximum deviation of half the diameter.

  • X or Y POSITION: Estimate the deviation of the X or Y positions of the end points of the cylinder.

These estimate values are calculated using statistical math. The values are standard deviation x 2, which means that we have 95% assurance that the these values are the maximum deviation.

Vtube-laser cylinderfitwindow.jpg

Wobble Deviation

To simplify terminology, we say that the highest of the X and Y values is the "wobble deviation". If the centerline calculation is very good, then wobble deviation decreases. If the calculation or fit is poor, then the wobble deviation is too high.

VTube-LASER uses the wobble deviation to determine if it should ask you to remeasure the cylinder.

Vtube-laser wobbledeviation.png

Default Cylinder Fit Tolerances

To allow VTube-LASER to warn for poor cylinder measurements, it stores tolerances for the allowed deviations during cylinder fit. These values are often setup in the Measure 1 tab of the System Options menu.

The default values are shown in the screen image on the right.

For less precise diameters like exhaust pipes, these settings usually work well. If you measure highly oval or deformed parts, it may be necessary to increase especially the X and Y Position tolerances.

Vtube-laser default CylinderFitTolerances.png


Recommended Aerospace Cylinder Fit Tolerances

Aerospace-grade materials are often very precise. For aerospace applications, we strongly recommend that you consider using tighter tolerances like these shown here.

The XY Positions should be 0.030" for longer straights, and 0.050" for shorter straights. ("Short" is also definable with the variable in the lower right corner. It is set to 2" length by default.)

Vtube-laser default CylinderFitTolerances aerospace.png

How to Test for Your Ideal Tolerances

You can test for ideal cylinder fit tolerance settings by watching the tolerance values in the Cylinder Fit window when measuring a tube.

If you notice that your material regularly measures with a certain wobble deviation, then you can adjust the tolerances in System Option to fit your application.

To change the default values, be sure to CLEAR the VTube-LASER project first, then press the "Set Project Default State to the current state" button. This will use the new default cylinder fit tolerances for all new projects.

Vtube set default project state to the current state.png

Other Pages